Liftmaster IHSL24UL Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Liftmaster IHSL24UL (60 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 125 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/60
INDUSTRIAL DC
VEHICULAR SLIDE GATE OPERATOR
INSTALLATION MANUAL
T BE INSTALLED AND
DANCE WITH THIS
ED GATE SYSTEMS
e on vehicular passage
ntended for use on
ates.
L24UL are intended
andIV vehicular slide
locate a professional
r area.
ompatible with myQ®
essories.
LiftMaster
300 Windsor Drive
Oak Brook, IL 60523
l support
Send it in by texting
the photo to 71403.
Take a photo of the
camera icon including
the points ( ).
1.
2.
L
IHSL24ULTECH
2
SAFETY 2
Safety Symbol and Signal Word Review ................................................2
Usage Class ...........................................................................................3
UL325 Entrapment Protection Requirements ........................................3
Safety Installation Information ...............................................................4
Role of Dealers, Installers, and Trained Gate System Technicians ........4
Role of End Users/Home Owners ..........................................................4
Gate Construction Information ...............................................................5
INTRODUCTION 6
Carton Inventory ....................................................................................6
Operator Specifications ..........................................................................7
Site Preparation .....................................................................................8
INSTALLATION 9
Step 1 Install the Operator .....................................................................9
Step 2 Attach the Chain .......................................................................11
Step 3 Install Entrapment Protection ...................................................12
Step 4 Earth Ground Rod .....................................................................15
Step 5 Power Wiring ............................................................................15
Step 6 Connect Batteries .....................................................................17
Step 7 Dual Gate Setup ........................................................................18
Step 8 Close and Secure the Door .......................................................20
Step 9 Install Warning Signs ...............................................................20
ADJUSTMENT 21
Limit, Speed, and Force Adjustment ....................................................21
Set the Initial Limits, Speed, and Force ...............................................21
Speed Control ......................................................................................22
Fine Tune the Force .............................................................................22
Adjust the Limits ..................................................................................23
Obstruction Test ..................................................................................23
PROGRAMMING 24
Remote Controls (Not Provided) .........................................................24
LiftMaster Internet Gateway (not provided) .........................................25
CAPXLV Connected Access Portal .......................................................25
myQ® Business™: ...............................................................................26
Erase All Transmitter and Keypad Codes .............................................26
Erase Limits .........................................................................................26
Constant Pressure Override (CPO) ......................................................26
Gate Hold Open Feature .......................................................................26
To Remove and Erase Monitored Entrapment Protection Devices .......26
OPERATION 27
Gate Operator Setup Examples ............................................................27
Control Board Overview .......................................................................28
Manual Disconnect ..............................................................................29
Reset Button ........................................................................................29
Operator Alarm ....................................................................................30
Remote Control ....................................................................................30
ACCESSORY WIRING 31
External Control Devices ......................................................................31
Locks 32 ...................................................................................................
Miscellaneous Wiring ...........................................................................32
EXPANSION AND RELAY ADAPTER BOARDS 33
Expansion and Relay Adapter Boards Overview ...................................33
Auxiliary Relays ...................................................................................34
Wiring Accessories to the Expansion Board ........................................35
MAINTENANCE 36
Important Safety Instructions ..............................................................36
Maintenance Chart ...............................................................................37
Batteries 37 ...............................................................................................
Drive Train ...........................................................................................37
TROUBLESHOOTING 38
Diagnostic Codes .................................................................................38
Control Board LEDs .............................................................................39
Troubleshooting Chart .........................................................................40
SOLAR PANELS 43
Solar Panel(s) ......................................................................................43
REPAIR PARTS 47
ACCESSORIES 48
WARRANTY 50
APPENDIX 51
SAMS Wiring With Relays Not Energized ............................................51
Dual Gate Settings ...............................................................................51
Manual Adjustments with a Remote Control .......................................52
Wiring Diagram ....................................................................................53
Diagnostic Codes Table .......................................................................55
Site Planning Safety Checklist .............................................................57
Contact Information .............................................................................60
WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
When you see these Safety Symbols and Signal Words on the following pages, they will alert
you to the possibility of if you do not comply with the warnings that Serious Injury or Death
accompany them. The hazard may come from something mechanical or from electric shock.
Read the warnings carefully.
When you see this Signal Word on the following pages, it will alert you to the possibility of
damage to your gate and/or the gate operator if you do not comply with the cautionary
statements that accompany it. Read them carefully.
IMPORTANT NOTE:
• BEFORE attempting to install, operate or maintain the operator, you must read and fully
understand this manual and follow all safety instructions.
• DO NOT attempt repair or service of your gate operator unless you are a Trained Gate
Systems Technician.
MECHANICAL
ELECTRICAL
TABLE OF CONTENTS
SAFETY
Safety Symbol and Signal Word Review
3
Usage Class
Class II - Commercial/General Access Vehicular Gate
A vehicular gate operator (or system) intended for use in a commercial location or
building such as a multi-family housing unit (five or more single family units), hotel,
garages, retail store, or other buildings accessible by or servicing the general public.
Class III - Industrial/Limited Access Vehicular Gate
A vehicular gate operator (or system) intended for use in an industrial location or
building such as a factory or loading dock area or other locations not accessible by or
intended to service the general public.
Class IV - Restricted Access Vehicular Gate Operator
A vehicular gate operator (or system) intended for use in a guarded industrial location
or building such as an airport security area or other restricted access locations not
servicing the general public, in which unauthorized access is prevented via
supervision by security personnel.
UL325 Entrapment Protection Requirements
Definitions
ENTRAPMENT: The condition when a person is caught or held in a
position that increases the risk of injury.
SLIDE GATE ENTRAPMENT ZONE: An entrapment zone exists if at any
point during travel, the gap between the gate and any opposing fixed
edge or surface such as posts, walls, pillars, columns, or the operator
itself, is less than 16" (406 mm) in a location up to 6 ft. (1.8 m) above
grade.
INDEPENDENT MONITORED ENTRAPMENT PROTECTION DEVICE: An
entrapment protection device is independent if it is a different type
(photoelectric sensors, edge device, inherent protection device) from the
other devices in the same entrapment zone.
Use the in the appendix to identifySite Planning Safety Checklist
entrapment zones found in your installation.
Requirements
•A independent monitored entrapment protectionminimum of two
devices are required to be installed at each entrapment zone.
•It is the responsibility of the installer to install external monitored
entrapment protection devices for .each entrapment zone
•The operator will only operate with a independentminimum of two
monitored entrapment protection devices installed in each direction;
two in the open direction and two in the closed direction.
This operator has an inherent entrapment protection device built-in.
The installer MUST provide one additional entrapment protection
device for each entrapment zone.
Acceptable entrapment protection device types include:
•Inherent (built into the operator)
•LiftMaster monitored external photoelectric sensors, see page 48 for
acceptable sensors.
•LiftMaster monitored external edge sensors, see page 48 for
acceptable sensors.
IMPORTANT SAFETY
INSTRUCTIONS
To reduce the risk of INJURY or DEATH:
•READ AND FOLLOW ALL INSTRUCTIONS.
•NEVER let children operate or play with gate controls. Keep the
remote control away from children.
•ALWAYS keep people and objects away from the gate. NO ONE
SHOULD CROSS THE PATH OF THE MOVING GATE.
•Test the gate operator monthly. The gate MUST reverse on
contact with an object or reverse when an object activates the
noncontact sensors. After adjusting the speed, force, or the
limit of travel, retest the gate operator. Failure to adjust and
retest the gate operator properly can increase the risk of
INJURY or DEATH.
•Use the manual release ONLY when the gate is not moving.
•KEEP GATES PROPERLY MAINTAINED. Read this manual. Have a
Trained Gate Systems Technician make repairs to gate hardware.
•The entrance is for vehicles ONLY. Pedestrians MUST use separate
entrance.
•SAVE THESE INSTRUCTIONS.


Product specificaties

Merk: Liftmaster
Categorie: Niet gecategoriseerd
Model: IHSL24UL

Heb je hulp nodig?

Als je hulp nodig hebt met Liftmaster IHSL24UL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Liftmaster

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd