Liftmaster 362LMC Handleiding

Liftmaster Niet gecategoriseerd 362LMC

Lees hieronder de đź“– handleiding in het Nederlandse voor Liftmaster 362LMC (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
To prevent possible SERIOUS INJURY or
DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach
of children. NEVER permit children to
operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be
seen clearly, is properly adjusted, and there
are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight
until completely closed. NEVER permit
anyone to cross path of moving gate or door.
INTRODUCTION
This product is for use with gate operators, commercial door operators and any LiftMaster
® product
that uses a 315 MHz fixed code. The single-button remote control will activate one device, the
2-button remote control will activate up to 2 devices, and the 3-button remote control will activate
up to 3 devices.
Model 361LM & 361LMC
Model 362LM & 362LMC
Model 363LM, 363LMC,
333LM, & 333LMC
Locate the Dip Switches on Your Remote Control
BEFORE YOU BEGIN
Locate the Smart/Learn Button for Your Product
Single-Button and 3-Button
Remote Controls:
Slide the battery cover open to access the dip
switches in the remote control.
2-Button Remote Control:
The 2-button remote control has two sets of
dip switches.
Slide the battery cover open to access the dip
switches for the smooth button. Remove the
screw on the back of the remote control and
remove the cover by pressing the tab. This will
access the dip switches for the ribbed button.
+
0
–
123456789
+
0
–
123456789
+
0
–
123456789
Tab
1
Single and 3-Button Remote Controls
2-Button Remote Controls
NOTE: Your product may look different than
the products illustrated.
The Smart/Learn button is typically located on
the logic board of the operator or external
receiver. Refer to your product owner’s manual
for the exact location of the Smart/Learn
button.
Smart/Learn Button
WARNING: This product can expose you to chemicals including lead, which are known to
the State of California to cause cancer or birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
SET THE DIP SWITCHES
1Press and release the Smart/Learn button
on your product. The LED will light.
2Within 30 seconds press and hold the
button on the remote control that you
wish to activate your product.
Programming is complete.
Repeat the steps above for each button and/or
remote control you would like to program.
Programming the remote control to
an existing remote control
Locate the dip switches in the new and old
remote controls. Place remote controls side by
side and set the dip switches in the remote
controls to matching positions (+,0,-).
Programming a 3-button remote
control
When programming a single or 2-button
remote control to a 3-button remote control it
is very important to set dip switch #1 to the
correct position. The dip switch in the single or
2-button remote control MUST correspond to
the buttons on the 3-button remote control as
shown.
Example: If you are programming a
single-button remote control to the middle
button on the 3-button remote control, dip
switch #1 in the single-button remote control
MUST be set to “0” in order for both buttons to
work.
PROGRAMMING
Programming the remote control
without an existing remote control
Set the dip switches in the remote controls to
any position you want (+,0,-).
+
0
–
123 456 789
=
+
0
–
123 456 789
+
0
–
123 456 789
=
2 3 4 5 6 7 8 9
+
0
–
123 456 789
=
+
0
–
1
+0
-
New Remote Control
New Remote Control
3-Button
Remote Control
Single or 2-Button
Remote Control
2
Dip switch #1 must
correspond to the
3-button remote
control buttons
Existing Remote Control
1
2
Use a pen or screwdriver to slide the dip switches.
Smart/Learn Button
PROGRAMMING MODEL 333LM ONLY
Install the control station and receiver where the door is visible, but away from the door and its
hardware. When a receiver is used to activate a commercial door opener, a reversing edge MUST
be installed on the bottom of the door. Failure to install a reversing edge under these
circumstances may result in SERIOUS INJURY or DEATH to persons trapped beneath the door.
Model 333LM 3-button remote controls can also be used with a 323LM 3-channel receiver and a
3-button door control to activate a commercial door operator in OPEN, CLOSE, and STOP mode.
1Use a screwdriver to pry open the receiver
cover.
2Verify that the slide switch on receiver is
set to the N.C. position (other wise the
commercial door operator will not
operate).
4Within 30 seconds press and release the
red button on the remote control. The red
button is now programmed for CLOSE
mode.
NOTE: If the remote control button is not
pressed within 30 seconds, the LED next
to the selected Smart/Learn button will
turn OFF. In that case, press the
Smart/Learn button again to repeat
programming.
3Press and release the Smart/Learn button
labeled “A” on the receiver. The adjacent
LED will flash.
5
Repeat the steps 3-4 above with the yellow button on the remote control and the receiver
Smart/Learn button “B” to program the CLOSE mode; and again with the green button on the remote
control and the receiver Smart/Learn button “C” to program the OPEN mode.
Replace the receiver cover.
3
1
3
4
5
“A” Smart/Learn Button
2N.C.
Slide
Switch

Product specificaties

Merk: Liftmaster
Categorie: Niet gecategoriseerd
Model: 362LMC

Heb je hulp nodig?

Als je hulp nodig hebt met Liftmaster 362LMC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Liftmaster

Liftmaster

Liftmaster CAPXSHOOD Handleiding

8 December 2023
Liftmaster

Liftmaster 041DJ003MC Handleiding

17 Augustus 2023
Liftmaster

Liftmaster myQ-SGC2WCH Handleiding

9 Juli 2023
Liftmaster

Liftmaster CAPXS Handleiding

9 Juli 2023
Liftmaster

Liftmaster 041D8006-1 Handleiding

9 Juli 2023
Liftmaster

Liftmaster IHSL24UL Handleiding

9 Juli 2023
Liftmaster

Liftmaster LJ8900W Handleiding

9 Juli 2023
Liftmaster

Liftmaster MGJ5011U Handleiding

8 Juli 2023
Liftmaster

Liftmaster 041A7767 Handleiding

8 Juli 2023
Liftmaster

Liftmaster 41K4629 Handleiding

8 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024