Liftmaster 050ACTWFLK Handleiding

Bekijk gratis de handleiding van Liftmaster 050ACTWFLK (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 18 mensen en kreeg gemiddeld 4.2 sterren uit 2 reviews. Heb je een vraag over Liftmaster 050ACTWFLK of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1

DANGER PELIGRO•

132C2280-3D

TO ERASE ALL

RECEIVER CODES

1. Pre ss and HOLD

re ce iver o range

ERASE button

6 se conds. Indicator

light will turn ON.

2. Rele ase butt on

whe n light t urns OFF.

CANADA:

PART : DE PIEZA:NO.NO.

DATE:

T HE CHAMBER LAIN

GRO UP, INC ., US A

Ens am blad o e n Méxic o

Ass em bled in Mexi co

ELIMINACIÓN DE

TODOS LOS CÓDIGOS DEL

RECEPTOR

1. MANTENGA PRES IONADO

e l botón naranja "ERASE "

de l rec ept or durant e 6

se gundos. La luz de l

indica dor se enc ende rá.

2. Sue lte el bo tón cuando la

luz se apague .

DANGER PELIGRO•

132C2280-3D

TO ERASE A LL

RECEIV ER CODE S

1.PressandHOLD

receivero range

ERASE bu tton

6 Indicato rseco nds.

lig h t wi ll turn ON.

2.Releasebu tton

when ligh t tu rns OF F.

CANADA:

P : ARTN O.N O.DEPIEZA:

DATE:

THE C HA M BER LAI N

GROU P, I NC ., U SA

EnsambladoenMéxico

AssembledMexico i n

ELIM INAC IÓN DE

TODOSLO S CÓD IGOS D EL RECEP TOR

1.P RES IONADO MANTENGA

el b otón naranja "ERASE "

d el receptor6 d u rante

segundos. La lu z del ind i cador seencend erá.

2.elcuando Suelte botón la

luz seapague.

Before you begin

1

Installation

RECEIVER LOGIC BOARD REPLACEMENT

Models 050ACTBMC and 050ACTBLKMC

Replaces 050ACTWF and 050ACTWFLK

1.2 To maintain your warranty, place the

provided label over the existing label

on the end panel of the garage door

opener.

1.1 Remove the light lens by pulling the

top sides of the light lens and rotate the

light lens down. Squeeze the light lens

clips to remove lens from end panel.

Your garage door opener has an internal gateway located on the receiver logic board. After installing the new receiver logic board, use the myQ

® serial number found on the provided label to add your

garage door opener to your myQ account. The products illustrated in the instructions are for reference. Your product may look different.

1.3 Disconnect power to the garage door

opener.

Remove the receiver logic board

2

2.1 Disconnect the wires from the quick-connect terminals (). A

Remove the receiver logic board end panel from the garage

door opener.

2.2 Unplug the wire harnesses from the receiver logic

board. You may need needle-nosed pliers to remove

the harnesses.

To prevent possible SERIOUS INJURY or

DEATH:

• Disconnect ALL electric and battery

power BEFORE performing ANY service

or maintenance.

To prevent damage to the receiver/logic

board, DO NOT touch printed circuit board

of replacement receiver/logic board during

installation.

ALWAYS wear protective gloves and eye

protection when changing the battery or

working around the battery compartment.

A

To insert or remove

the wires from the

terminal, push in the

tab with a

screwdriver tip.

Red

White

White

Grey

2.3 Remove the receiver

logic board from the

end panel by removing

the 2 screws and

releasing the 2 clips.

Screws

Wire clip

Clips

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth

defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Product specificaties