Leisure VHL1 Handleiding

Bekijk gratis de handleiding van Leisure VHL1 (4 pagina’s), behorend tot de categorie Spoelbak. Deze gids werd als nuttig beoordeeld door 63 mensen en kreeg gemiddeld 4.3 sterren uit 7 reviews. Heb je een vraag over Leisure VHL1 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1970-02

2.Fitthexingclipstothe

sinkusingthescrews

provided,asshownin

g.2andhingethem

backawayfromthe

sinkedge.

3.Atthispointtrythesink

inthecut-out,some

localisedenlargement

oftheholemaybe

necessaryaroundthe

clips.

4.Fitthetaptothe

sink.

5.Fitthewastestothesinkfollowingtheinstructions

packedwiththem.

6.Fitthefoamsealtotheedgeofthesink.Peeloffthepaper

backingstripandstickthesealtotherecessinthesink

asshowning.3.Ensurethataneatbuttjointisachieved

wheretheendsofthesealmeet.

FITTINGTHESINK

1.Positionthesinkinthecut

out.

2.Tensionthexingclipsas

showning.4.

Ensurethatthefoamseal

iscarefullycompressed

butdonotovertightenthe

clips.

3.Completetheplumbingof

thehotandcoldsupplyto

thetap.

ALTERNATIVEMETHODOFSEALING

1.Applysiliconesealant(notsupplied)totheundersideof

thesinkrim,asshowning.5.

2.Removesurplussealantfromaroundthesinkusingadamp

cloth.

NOTE:Duringinstallationcareshouldbetakentoensure

thesinkisprotectedfromscuffsandscratches.Strainingand

overtighteningofallplumbingxturesconnectedtothesink

shouldbeavoided.Installersshouldcarefullycheckthatthe

mouldingandtheedgesofthesinkaredeadlevelsothat

waterwillowoffthedrainer.

PLEASEREADTHOROUGHLYBEFOREATTEMPTINGTO

INSTALLSINK.

PREPARINGTHEWORKTOP

1.Itisrecommendedthattheinsetsinkisttedtotheworktop

beforebeingpermanentlyxedtothecabinet.

2.Placethesinkupsidedownonworktop.Positionthesink

relativetotheworktopasrequired,ensuringthatthecabinet

frameworkwillbeclearofallpartsofthesink.

Withasharpsoftpencildrawroundsinkasaccuratelyas

possible.Seeg.1.

3.Removethesinkanddrawanotherline10mminside

theout-lineofthesinktop.Thisisthecuttinglineforthe

aperture.

4.Drillaslargeaholeaspossibleinsidethecuttingline.Using

apadsaw,jigsaworsimilar,cutouttheaperture.Atthis

pointwewouldrecommendthattheworktopapertureis

sealed.Todothispaintoverwithap.v.a.adhesive,paint,

varnishorsmearwithsiliconesealant.

PREPARINGTHESINK

1.Ifatapholeisrequired,buthasnotbeensuppliedinthe

sink,proceedasfollows.

Decidewhetherthebowlistobeontheleftorrighthand

whenthesinkistted.Cuttheappropriatetapholeinto

thesink.Todothisyouwillneedaholesawortankcutter

settocutouta35mmdiameterholeandapilotdrill.On

thereversesideofthesinkyouwillndalocationpoint

forthepilotdrillinthecentreofthetapcut-out.Drillout

thepilothole.TurnthesinkoverandcarefullydrilLcOt4he

tap-hole.

WARNING: Velstra&Neostoneproductsincludeasilicaller.

Anymachiningoperationwillproduceneparticlesofdust.

Drillingorcuttingmustbecarriedoutinawell-ventilated

area.

INSTALLATIONDETAILSVELSTRA

®

&NEOSTONESINKS

Product specificaties