Leisure NHL2 Handleiding


Pagina's 4 Engels Spoelbak

Bekijk de handleiding van Leisure NHL2 gratis online of download de PDF. Deze handleiding is 35 keer bekeken. Vraag over dit model? Stel een vraag

1970-02
2.Fitthexingclipstothe
sinkusingthescrews
provided,asshownin
g.2andhingethem
backawayfromthe
sinkedge.
3.Atthispointtrythesink
inthecut-out,some
localisedenlargement
oftheholemaybe
necessaryaroundthe
clips.
4.Fitthetaptothe
sink.
5.Fitthewastestothesinkfollowingtheinstructions
packedwiththem.
6.Fitthefoamsealtotheedgeofthesink.Peeloffthepaper
backingstripandstickthesealtotherecessinthesink
asshowning.3.Ensurethataneatbuttjointisachieved
wheretheendsofthesealmeet.
FITTINGTHESINK
1.Positionthesinkinthecut
out.
2.Tensionthexingclipsas
showning.4.
Ensurethatthefoamseal
iscarefullycompressed
butdonotovertightenthe
clips.
3.Completetheplumbingof
thehotandcoldsupplyto
thetap.
ALTERNATIVEMETHODOFSEALING
1.Applysiliconesealant(notsupplied)totheundersideof
thesinkrim,asshowning.5.
2.Removesurplussealantfromaroundthesinkusingadamp
cloth.
NOTE:Duringinstallationcareshouldbetakentoensure
thesinkisprotectedfromscuffsandscratches.Strainingand
overtighteningofallplumbingxturesconnectedtothesink
shouldbeavoided.Installersshouldcarefullycheckthatthe
mouldingandtheedgesofthesinkaredeadlevelsothat
waterwillowoffthedrainer.
PLEASEREADTHOROUGHLYBEFOREATTEMPTINGTO
INSTALLSINK.
PREPARINGTHEWORKTOP
1.Itisrecommendedthattheinsetsinkisttedtotheworktop
beforebeingpermanentlyxedtothecabinet.
2.Placethesinkupsidedownonworktop.Positionthesink
relativetotheworktopasrequired,ensuringthatthecabinet
frameworkwillbeclearofallpartsofthesink.
Withasharpsoftpencildrawroundsinkasaccuratelyas
possible.Seeg.1.
3.Removethesinkanddrawanotherline10mminside
theout-lineofthesinktop.Thisisthecuttinglineforthe
aperture.
4.Drillaslargeaholeaspossibleinsidethecuttingline.Using
apadsaw,jigsaworsimilar,cutouttheaperture.Atthis
pointwewouldrecommendthattheworktopapertureis
sealed.Todothispaintoverwithap.v.a.adhesive,paint,
varnishorsmearwithsiliconesealant.
PREPARINGTHESINK
1.Ifatapholeisrequired,buthasnotbeensuppliedinthe
sink,proceedasfollows.
Decidewhetherthebowlistobeontheleftorrighthand
whenthesinkistted.Cuttheappropriatetapholeinto
thesink.Todothisyouwillneedaholesawortankcutter
settocutouta35mmdiameterholeandapilotdrill.On
thereversesideofthesinkyouwillndalocationpoint
forthepilotdrillinthecentreofthetapcut-out.Drillout
thepilothole.TurnthesinkoverandcarefullydrilLcOt4he
tap-hole.
WARNING: Velstra&Neostoneproductsincludeasilicaller.
Anymachiningoperationwillproduceneparticlesofdust.
Drillingorcuttingmustbecarriedoutinawell-ventilated
area.
INSTALLATIONDETAILSVELSTRA
®
&NEOSTONESINKS

Beoordeel deze handleiding


Product specificaties

Merk: Leisure
Categorie: Spoelbak
Model: NHL2
Kleur van het product: Zwart
Breedte: 980 mm
Diepte: 508 mm
Soort wastafel: Opbouwwasbak
Vorm gootsteen: Rechthoekig
Aantal gootstenen: 2 kommen
Vorm eerste spoelbak: Rechthoekig
Eerste kom dimensies (WxL): 350 x 433 mm
Eerste kom diepte: 180 mm
Vorm tweede spoelbak: Rechthoekig
Tweede kom dimensies (WxL): 154 x 298 mm
Tweede kom diepte: 114 mm
Kraangat: Ja
Tap-gat grootte: 35 mm
Aantal kraangaten: 2
Aanrecht: Ja

Heb je hulp nodig?

Als je hulp nodig hebt met Leisure NHL2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden