Lasko CT30300 Handleiding


Pagina's 8 Heater

Bekijk de handleiding van Lasko CT30300 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag

New 3/26
1
CT30300ES
Used for Model:
CT30300
READ AND SAVE THESE INSTRUCTIONS
Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself
and others by observing all safety information. Failure to comply with instructions could result in personal injury
and/or property damage!
This heater is for residential use only. It is not intended to be used in commercial, industrial
or agricultural settings.
Please Do Not Return Product to Store!
Chat with us at www.lasko.com Monday-Friday 8am - 9pm EST
(Valid in U.S. and Canada only)
Register Your P
You will benet fr
•
Efcient and enh
•
Future product u
Ceramic Tower Heater with Remote Control
Instruction Manual
New 3/26
2
CT30300ES
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of re, electrical shock, injury to persons and hyperthermia:
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS FOLLOW
THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
Plug heaters directly into a 120v wall outlet/receptacle only. Never use with an extension cord. Do not plug heater into any other cord connected
device, such as a power strip, surge protector, multiple outlet adapter, cord reel or outlet-type air freshener. The use of such devices may create a
re hazard. Do not plug multiple devices in the same outlet or on same circuit as heater.
Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that heater plug ts tightly into outlet before each use. During use,
check to make certain the heater plug is not overheating. If necessary have a qualied electrician check and/or replace the wall outlet. Do not use
this heater with any solid state speed control devices.
Make certain that the power source conforms to the electrical requirements of the heater.
Extreme caution is necessary when any heater is used by or near children or invalids. The heater should not be left operating unattended. Never
leave children unattended when the heater is on or plugged in.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended tot in a
polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a qualied electrician. Do not
attempt to defeat this safety feature.
Do not use the heater in areas where gasoline, paint, or ammable liquids are used or stored. Do not use heater in locations where ammable or
explosive chemicals are stored, or in wet atmospheres.
Do not operate any heater with a damaged cord or plug or after the heater malfunctions, or has been dropped or damaged in any manner. To
disconnect heater, turn the heater off then remove the plug from the outlet.
Always unplug heater when not in use. Unplug power cord before servicing or moving the heater.
Do not insert or allow ngers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, re, or damage the
heater. Do not block or tamper with the heater in any manner while it is in operation.
Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not
depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug the power cord.
Hyperthermia can result in death. Symptoms of hyperthermia include high body temperature, headache, nausea, vomiting, tiredness, dizziness,
fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seek medical attention.
To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave product running unattended in a conned space around
infants, or individuals with reduced physical, sensory, or mental capabilities.
WARNING
READ ALL INSTRUCTIONS BEFORE USING THIS HEATER.
•
Always unplug heater when not in use. Unplug power cord before servicing or moving the heater.
•
Do not insert or allow ngers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, re, or damage
the heater. Do not block or tamper with the heater in any manner while it is in operation.
•
Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not
depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug the power cord.
•
Always place the heater on a stable, at, level surface when operating, to avoid the chance of the heater overturning. Locate the power cord
so the heater or other objects are not resting on it. Do not run power cord under carpeting. Do not cover power cord with throw rugs, runners,
or similar coverings as this may cause cord to overheat. Arrange power cord away from room trafc and where
it will not be tripped over.
•
This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this heater. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 M) from the front of the heater and
keep them at least 1 foot (0.3 M) from the sides and rear.
•
This heater is not intended for use in wet or damp locations. This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. Never locate a heater where it may fall into a bathtub or other water container.
•
Do not use heater outdoors.
•
This heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are conned. Please refer
to national electric code (nec) article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for
agricultural buildings. This heater does not meet the requirements of nec article 547-7 (2008).
•
This heater is not suitable for use in hazardous locations. Please refer to national electric code (nec) article 500 or applicable state or local
codes or standards relating to electrical requirements for hazardous locations. This heater does not meet the requirements of
nec article 500 (2008).
•
Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this heater. If this occurs, move
the heater to another location.
•
Keep heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the heater.
•
Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause re, electric shock, or
injury to persons.
CAUTION
SAVE THESE INSTRUCTIONS
REMOTE CONTROL:
•
Install two “AAA” batteries (not included).
•
Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc)
or rechargeable (nickel-cadmium) batteries.
•
Do not dispose of batteries in re. Batteries may explode or leak.
•
Always purchase the correct size and grade of battery most suitable
for the intended use.
•
Replace all batteries of a set at the same time.
•
Clean the battery contacts and also those of the device prior to
battery installation.
•
Ensure the batteries are installed correctly with regards to polarity (+ and -).
•
Remove batteries from equipment that is not to be used for an
extended period of time.
•
Remove used batteries promptly.
New 3/26
3
CT30300ES
Par
Controls
1
1
se A
se B
2
2
3
4
Assembly
Base A
Ba
1.
Align the slots on Base A with
tabs on Base B. Snap together.
Front
Locked
Hooks
2. Lay the unit on a sturdy table for easier
base assembly. Align the locator pin
and hooks on the Body of unit with the
corresponding slots on the Base.
3. Align the slots on the base with the hooks on
the unit. Turn clockwise to lock in place.
*AUTO ECO
™
THERMOSTAT
Pressing the () or () buttons while in any Heater function or speed will turn on the Auto Eco
™
function.
1.Tosettheroomtoaspecictemperature,pressthe(+)or(–)buttonstoselectthedesiredtemperature.Thetemperaturedisplaywillash.Theunitisnowin
Auto Eco
™
Mode.
2.Whenyoureachthetemperatureatwhichyouwanttosettheunit,thesettemperaturewillashseveraltimesandthenthedisplaywillreturntoindicatethe
current room temperature and will gradually change as the room temperature changes. NOTE: the temperature display does not indicate the temperature of the
heated air being emitted by the Unit.
3. Heater will run on HIGH heat when the ambient temperature is less than the set temperature.
4. Heater will run on LOW heat when ambient temperature reaches set temperature and will continue to run on LOW heat until ambient temperature reaches 2
degreesfahrenheitabovesettemperature.
5.HeaterwillturnOFFoncetheambienttemperatureisgreaterthan2degreesfahrenheitabovesettemperature.Thefanwillcontinuetorunfor15seconds
aftertheheaterelementisturnedo.
AllofthishappensautomaticallywithLaskoAutoEco™Technology.TodeactivatetheAutoEco™function,turntheoorpress
Unit
the heat mode button.
NOTE:
InAutoEco™,the
Unit will display the current room temperature in ° Fahrenheit. Press the ) and ( buttons at the same time to change the ()
display to° Celsius. Press the same two buttons together again to change the display back to ° Fahrenheit.
Timer Button
The timer can be set for up to 12 hours. Continue
pressing the Timer Button to reach the desired time
setting.Timerlightilluminateswhenactivated.
Power Button
Turn Heater ON/OFF by pressing
the Power Button.
Base Oscillation Button
Press to Start/Stop the Base
Oscillation function.
Heat Mode Button
PresstocyclebetweenHigh,
Medium,andLowHeat.
*
Auto Eco
™
Thermostat Button
()+
Press to increase the desired room temperature.
*
Auto Eco
™
Thermostat Button()
-
Press to decrease the desired room temperature.
Display Snooze Button
Press to turn your display ON or OFF
(Remote control only)
AUTO-DIMMING DIGITAL DISPLAY
After 10 seconds the lights on the display will automatically dim.
Touching any button will reilluminate the lights to 100%.
Beep Mute Mode
Press to turn off the beep sound of function
selections (Remote control only)

Beoordeel deze handleiding


Product specificaties

Merk: Lasko
Categorie: Heater
Model: CT30300

Heb je hulp nodig?

Als je hulp nodig hebt met Lasko CT30300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden