Lasko CT22520 Handleiding
Pagina's 8 Heater
Bekijk de handleiding van Lasko CT22520 gratis online of download de PDF. Deze handleiding is 1 keer bekeken. Vraag over dit model? Stel een vraag
New 3/26CT22520ES
1
Used for Models:
CT22520
READ AND SAVE THESE INSTRUCTIONS
Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself
and others by observing all safety information. Failure to comply with instructions could result in personal injury
and/or property damage!
This heater is for residential use only. It is not intended to be used in commercial, industrial
or agricultural settings.
Have a Question? Need a Part?
Please Do Not Return Product to Store!
Chat with us at www.lasko.com Monday-Friday 8am - 9pm EST
(Valid in U.S. and Canada only)
Halo
™
Ceramic Tower Heater
with Remote Control
Instruction Manual
Register Your Product Today
You will benet from:
•
Efcient and enhanced support
•
Future product updates
This product is equipped with PowerGuard
™
.
PowerGuard
™
monitors the outlet voltage to detect poor
outlet connections that can cause overheating. If an unsafe
condition is detected, the heater will shut o and alert you
to protect the unit and your home.
PowerGuard
™
must be manually enabled. It will
remain active until manually disabled.
How to enable PowerGuard
™
:
•
Plug in and turn the unit on
•
Press and hold the
“
+
”
and buttons for 5 seconds
•
A 5-second countdown will display during the hold duration
•
PowerGuard
™
icon will illuminate on display with an audible
beep, signaling it is enabled*
a.
* Icon will stay illuminated until PowerGuard
™
is disabled
If PowerGuard
™
is enabled and senses an unsafe voltage at the
outlet, the heater will automatically switch into protective state.
When this happens, you will notice the following:
•
The heater will safely shut o
•
PowerGuard
™
icon will blink and unit will beep
•
Display will show an “E1” error message
•
All other display lights turn o, expect the power light
To reset the heater, unplug it from the outlet. If the heater still
doesn’t work, it’s likely it’s caused by a faulty or loose outlet
connection. Try a dierent outlet for optimal performance.
PowerGuard
™
will remain enabled/disabled through a power cycle
How to disable PowerGuard
™
:
•
Make sure unit is on
•
Press and hold the
‘
+
’
and buttons for 5 seconds
•
A 5-second countdown will display during the hold duration
•
PowerGuard
™
icon illumination will turn o with an audible
beep, signaling it is disabled
PowerGuard
™
New 3/26CT22520ES
2
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of re, electrical shock, injury to persons and hyperthermia:
USE THIS HEATER ONLY AS DESCRIBED IN THIS MANUAL. ANY OTHER USE NOT RECOMMENDED BY THE MANUFACTURER
MAY CAUSE FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:
Plug heaters directly into a 120v wall outlet/receptacle only. Never use with an extension cord. Do not plug heater into any other cord connected
device, such as a power strip, surge protector, multiple outlet adapter, cord reel or outlet-type air freshener. The use of such devices may create a
re hazard. Do not plug multiple devices in the same outlet or on same circuit as heater.
Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that heater plug ts tightly into outlet before each use. During use,
check to make certain the heater plug is not overheating. If necessary have a qualied electrician check and/or replace the wall outlet. Do not use
this heater with any solid state speed control devices.
Make certain that the power source conforms to the electrical requirements of the heater.
Extreme caution is necessary when any heater is used by or near children or invalids. The heater should not be left operating unattended. Never
leave children unattended when the heater is on or plugged in.
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to t in a
polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a qualied electrician. Do not
attempt to defeat this safety feature.
Do not use the heater in areas where gasoline, paint, or ammable liquids are used or stored. Do not use heater in locations where ammable or
explosive chemicals are stored, or in wet atmospheres.
Do not operate any heater with a damaged cord or plug or after the heater malfunctions, or has been dropped or damaged in any manner. To
disconnect heater, turn the heater off then remove the plug from the outlet.
Always unplug heater when not in use. Unplug power cord before servicing or moving the heater.
Do not insert or allow ngers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, re, or damage the
heater. Do not block or tamper with the heater in any manner while it is in operation.
Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not
depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug the power cord.
Hyperthermia can result in death. Symptoms of hyperthermia include high body temperature, headache, nausea, vomiting, tiredness, dizziness,
fainting, and rapid pulse. If you begin to experience symptoms related to hyperthermia, turn off the heater and seek medical attention.
To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave product running unattended in a conned space around
infants, or individuals with reduced physical, sensory, or mental capabilities.
WARNING
•
Always unplug heater when not in use. Unplug power cord before servicing or moving the heater.
•
Do not insert or allow ngers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, re, or damage
the heater. Do not block or tamper with the heater in any manner while it is in operation.
•
Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not
depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug the power cord.
•
Always place the heater on a stable, at, level surface when operating, to avoid the chance of the heater overturning. Locate the power cord
so the heater or other objects are not resting on it. Do not run power cord under carpeting. Do not cover power cord with throw rugs, runners,
or similar coverings as this may cause cord to overheat. Arrange power cord away from room trafc and where
it will not be tripped over.
•
This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this heater. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 M) from the front of the heater and
keep them at least 1 foot (0.3 M) from the sides and rear.
•
This heater is not intended for use in wet or damp locations. This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. Never locate a heater where it may fall into a bathtub or other water container.
•
Do not use heater outdoors.
•
This heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are conned. Please refer
to national electric code (nec) article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for
agricultural buildings. This heater does not meet the requirements of nec article 547-7 (2008).
•
This heater is not suitable for use in hazardous locations. Please refer to national electric code (nec) article 500 or applicable state or local
codes or standards relating to electrical requirements for hazardous locations. This heater does not meet the requirements of
nec article 500 (2008).
•
Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this heater. If this occurs, move
the heater to another location.
•
Keep heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the heater.
CAUTION
REMOTE CONTROL:
•
Install two “AAA” batteries (not included).
•
Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc)
or rechargeable (nickel-cadmium) batteries.
•
Do not dispose of batteries in re. Batteries may explode or leak.
•
Always purchase the correct size and grade of battery most suitable
for the intended use.
•
Replace all batteries of a set at the same time.
•
Clean the battery contacts and also those of the device prior
to battery installation.
•
Ensure the batteries are installed correctly with regards to polarity (+ and -).
•
Remove batteries from equipment that is not to be used for an
extended period of time.
•
Remove used batteries promptly.
READ ALL INSTRUCTIONS BEFORE USING THIS HEATER.
SAVE THESE INSTRUCTIONS
New 3/26CT22520ES
3
Digital Display
Eco Mode
- Lights up when Eco mode is activated.
Auto temperature control will operate in low
heat setting.
Auto Mode
-Lights up when Automatic temperature
mode is set from high or medium heat.
Fan Only Mode
-Fan can be adjusted to F2 (High), F1
(Low)
PowerGuard
™
- The PowerGuard
™
icon blinks and unit
beeps if the heater detects a poor outlet connection that
can cause overheating.
Timer light illuminates when activated.
Timer Mode -
Child Lock light illuminates when activated.
Child Lock -
4
Parts Included
1 Body
4 Remote Control
2 Support Base A
3 Support Base B
2
3
2. Lay the unit on a sturdy table for easier base
assembly. Line up tabs of the heater base as
shown above.
Assembly
1. Align the slots on with tabs on
Base A
Base B
.
Snap Together.
3he
until
Base A
Base B
1
Tabs
Tabs
Support
Base
Power Button
- Turn Heater ON/OFF by pressing the
Power Button
Base Oscillation Button
Press to Start/Stop the Base
Oscillation function.
Timer Button
-The timer can be set up to 12 hours. 0.5
- 12.0 hours in 0.5-hour intervals up to 2 hours, 1-hour
increments from 2 hours to 12 hours. Continue pressing
the Timer Button to reach the desired time setting.
Heat Mode Button
-
Press to cycle between High,
Medium and Low Heat.
Fan Only Mode Button
- Fan can be adjusted to
F2 (High), F1 (Low).
* Automatic Thermostat Button (+) -
Press to
Increase the desired room temperature. (*See Page 4)
* Automatic Thermostat Button (
–
) -
Press to
Decrease the desired room temperature. (*See Page 4)
Beep Mute Mode -
Press to turn o the beep sound of
function selections.
Display Snooze Button
-
Press to turn your display
ON or OFF
CHILD LOCK-ON (Enable) -
When the Timer Button
and Display Dimmer Button are held together for 3
seconds, all heater functions are disabled, except
for the Power Button. All functions that are currently
activated will stay on.
CHILD LOCK-OFF (Disable) -
To turn o child lock,
press the Timer Button and Display Dimmer Button
together for 3 seconds. The child lock funtion will turn
o. Unplugging the unit will also disable the unit.
Controls
AUTO-DIMMING DIGITAL DISPLAY
After 10 seconds the lights on the display will automatically
dim.Touching any button will reilluminate the lights to 100%.
ROOM TEMPERATURE DISPLAY
Digital display shows room temperature in all heat modes.
HEAT MODES
High Heat = 3 Dots
Medium Heat = 2 Dots
Low Heat = 1 Dot
Power
Light
Child Lock
PowerGuard
™
Auto Mode
Fan Mode
Eco Mode
Timer
Product specificaties
| Merk: | Lasko |
| Categorie: | Heater |
| Model: | CT22520 |
Heb je hulp nodig?
Als je hulp nodig hebt met Lasko CT22520 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden