Lascar Electronics EL-USB-1-PRO Handleiding

Lascar Electronics Meetapparatuur EL-USB-1-PRO

Bekijk gratis de handleiding van Lascar Electronics EL-USB-1-PRO (2 pagina’s), behorend tot de categorie Meetapparatuur. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.8 sterren uit 2 reviews. Heb je een vraag over Lascar Electronics EL-USB-1-PRO of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/2

We recommend that a new CR1620 battery is used if any low battery state is detected by the software or if a large proportion of the

typical 30 day battery life has been consumed. Remove the screw. Pull the two halves of the case apart. Remove the old battery. Insert

the new battery. Assemble the two halves of the case. Insert the screw and tighten.

EL-USB-LITE

REPLACING YOUR DATA LOGGER’S BATTERY

Your data logger is provided with a 3.6V 1/2AA battery already installed. You can change the battery by following the instructions below.

DOWNLOAD AND INSTALL

EASYLOG USB SOFTWARE

Windows™ 7/8/10 (32 & 64bit)

Visit and click www.easylogusb.com

‘Download’. Once downloaded, install the

software. You may need administrator

permissions to do so.

•Insert the data logger into an available USB port on

your computer.

•Double click on the EasyLog USB icon on

your Windows™ desktop. This will load

the conguration software. Click ‘Set

up and start the USB data logger’ and

follow the set-up wizard.

•When setup is complete, the data logger should be

removed from the USB port. Do not leave your data

logger in the USB port for extended periods as this will

cause some of the battery capacity to be lost (with the

exception of EL-USB-1-RCG as this is a rechargeable

device).

•You can also download the data from a logger that has

been recording or view previously saved data from the

software. After doing so, remember to set-up and start your

logger to begin a new logging session.

USING THE SOFTWARE

Before using the data logger you will need to insert the 3.6V 2/3AA High Temperature battery provided, following the instructions below.

EL-USB-1 PRO

The EL-USB-1-RCG’s battery is preinstalled. To charge the battery, connect to a USB port with a USB cable until the green LED shows.

The rechargeable battery should only be replaced by an authorized supplier. Note that only the battery of the EL-USB-1-RCG is

rechargeable. Do not attempt to recharge any other device.

EL-USB-1-RCG

EL-USB

For a full product datasheet for your data logger

or for more information on the rest of the EasyLog range visit

www.lascarelectronics.com/data-loggers

Temperature

Temperature/

Relative Humidity

Event, State &

Count

Thermocouple

Voltage

Current

Carbon Monoxide

Thermistor

IMPORTANT SAFETY INFORMATION

Disposal and Recycling Information

You must dispose of Lascar products in accordance with relevant laws and regulations. They contain

electronic components and lithium batteries and therefore must be disposed of separately from

household waste.

Repairing or Modifying

Never attempt to repair or modify Lascar products. Dismantling them, other than for the purpose of

changing replaceable batteries, may cause damage that is not covered under the warranty. Servicing

should only be provided by an authorized supplier.

EL-USB-LITE

Green single ash

The data logger is

currently logging. No

alarm.

Red single ash

The data logger is

currently logging. Low

alarm.

Red double ash

The data logger is

currently logging. High

alarm.

No LEDs ash

The data logger is

stopped, the baery

is empty or there is no

baery ed.

EL-USB (excluding EL-USB-1-PRO)

Green double ash

The data logger is not cur-

rently logging, but is primed

to start at a later date and

me (delayed start).

Green single ash

The data logger is currently

logging. No alarm.

Green and Amber single ash

The data logger is full and has

stopped logging. No alarm.

Red single ash

The data logger is currently

logging. Low alarm.

Red and Amber single ash

The data logger is full and has

stopped logging. Low alarm.

Red double ash

The data logger is currently

logging. High alarm.

Red and Amber double ash

The data logger is full and has

stopped logging. High alarm.

Amber single ash

The baery is running low.

Data logging will connue

unl the baery voltage

drops below 2.8V.

No LEDs ash

The data logger is stopped,

the baery is empty or there

is no baery.

Green single ash (every 30s)

The data logger is not currently

logging, but is primed to

start at a later date and me

(delayed start)

Green single ash (every 10s)

The data logger is currently

logging. No alarm.

Red single ash (every 10s)

The data logger is currently

logging. Low alarm.

Red double ash (every 10s)

The data logger is currently

logging. High alarm.

Green single ash (every 20s)

The data logger is currently

logging. Low baery.

Red single ash (every 20s)

The data logger is currently

logging, however the baery is

running low. Low alarm.

Red double ash (every 20s)

The data logger is currently

logging, however the baery is

running low. High alarm.

Green double ash (every 20s)

The data logger is full and has

stopped logging.

Red & Green single ash

alternately (every 20s)

The data logger is full and

has stopped logging. High or

low alarm.

No LEDs ash

The data logger is stopped, the

baery is empty or there is

no baery.

EL-USB-1-RCG

Iss 13_06-2019

www.lascarelectronics.com/data-loggers

SALES & SUPPORT

Disclaimer:

Every effort has been made to ensure the accuracy of this publication and no responsibility or liability can be accepted by Lascar Electronics Limited

for any errors or omissions in the content of this document. Data and legislation may change, and so we strongly advise you to obtain and review the

most recently issued regulations, standards, and guidelines. This publication does not form the basis of a contract.

T +44 (0) 1794 884567

E sales@lascar.co.uk

T +1 (814) 835-0621

E us-sales@lascarelectronics.com

USA

T +852 2389 6502

E sales@lascar.com.hk