Lancom GS-3152XSP Handleiding

Lancom Schakelaar GS-3152XSP

Lees hieronder de 📖 handleiding in het Nederlandse voor Lancom GS-3152XSP (2 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

T E C H N I C A L D A T A

LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks

of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for

technical errors and / or omissions. 111584/0120

Hardware

Power supply Exchangeable power supply (110-230 V, 50-60 Hz)

Power consumption Max. 920 W when using one PSU, max. 1840 W when using two PSUs

Environment Temperature range 0–40° C; short term temperature conditions 0–50°C; humidity 10–90%;

non-condensing

Housing Robust metal housing, 19“ 1U (442 x 44 x 440 mm > W x H x D) with removable mounting

brackets, network connectors on the front

Number of fans 2 (3 when using 2 PSUs)

Interfaces

ETH

SFP

A48 TP Ethernet ports 10/100/1000 Mbps

A4 10 G SFP+ ports 1 / 10 Gbps

A52 concurrent ports in total

Declaration of Conformity

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in

compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of

the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc

Package Content

Documentation Quick Reference Guide (DE/EN), Installation Guide (DE/EN)

Mounting brackets Two 19” brackets for rack mounting;

If an additional rear support surface is required for more stable mounting of the switch,

please use the LANCOM Switch Rack Mount L250, item no.: 61432, which is available as an

accessory.

Power supply unit 1x exchangeable power supply LANCOM SPSU-920

(expandable up to 2 PSUs for redundancy / higher PoE budget)

Cable 1 IEC power cord, 1 serial configuration cable 1.5 m

M O U N T I N G A N D C O N N E C T I N G T H E D E V I C E

d 10 G SFP+ ports

Off Port inactive or disabled

Blue Link 10 Gbps

Blue, blinking Data transfer, link 10 Gbps

Green Link 1 Gbps

Green, blinking Data transfer, link 1 Gbps

c TP Ethernet ports

LEDs switched to Link/Act/Speed mode

Off Port inactive or disabled

Green Link 1000 Mbps

Green, blinking Data transfer, link 1000 Mbps

Orange Link < 1000 Mbps

Orange, blinking Data transfer, link < 1000 Mbps

LEDs switched to PoE mode

Off Port inactive or disabled

Green Port enabled, power supply to connected

device

Orange Hardware error

b ca

aConfiguration interface (Console)

Connect the configuration interface via the included serial

configuration cable to the serial interface of the device you want to

use for configuring / monitoring the switch.

bTP Ethernet interfaces

Use Ethernet cables to connect the interfaces 1 to 48 to your PC or

a LAN switch.

cSFP+ interfaces

Insert suitable LANCOM SFP modules into the SFP+ inter faces

49 to 52. Choose cables which are compatible with the SFP

modules and connect them as described in the module’s

documen tation.

dPower supply modules with power connectors

(device back side)

Supply power to the device via the power connectors of the

power supply modules on the device’s back side. Please use the

IEC power cables supplied (not for WW devices) or country-

specific LANCOM Power Cords.

Please observe the following when setting up the device

AThe mains plug of the device must be freely accessible.

AFor devices to be operated on the desktop, please attach the adhesive rubber

footpads.

ADo not rest any objects on top of the device and do not stack multiple devices.

A Keep all ventilation slots of the device clear of obstruction.

AMount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets.

If an additional rear support surface is required for more stable mounting of the switch, please use the

LANCOM Switch Rack Mount L250.

APlease note that support for third-party accessories (SFP and DAC) is not provided.

LANCOM GS-3152XSP

Quick Reference Guide

C ud eadylo -r

b Mode/Reset button

Short press Port LED mode switch

~5 sec. pressed Device restart

7~12 sec. pressed Configuration reset and device restart

a System / PWR A / PWR B / Link/Act/Speed / PoE

System: off Device powered off

System: green Device operational

System: red Hardware error

PWR A / PWR B: off

PWR A / PWR B: green

Link/Act/Speed: green Port LEDs show link / activity status or

port speed

PoE: green Port LEDs show PoE status

b dca c

e f

e f Power supply unit LEDs

DC OK: green, blinking Secondary power supply OK

DC OK: red, blinking Secondary power supply failure

AC OK: green, blinking Primary power supply OK

AC OK: red, blinking Primary power supply failure

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!

Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

Product specificaties

Merk:	Lancom
Categorie:	Schakelaar
Model:	GS-3152XSP
Kleur van het product:	Zwart
Breedte:	442 mm
Diepte:	300 mm
Hoogte:	44 mm
Materiaal behuizing:	Metaal
LED-indicatoren:	Ja
Vormfactor:	1U
Meegeleverde kabels:	AC
Snelstartgids:	Ja
Vermogensverbruik (max):	65 W
Netwerkstandaard:	IEEE 802.1x, IEEE 802.3af, IEEE 802.3at, IEEE 802.3az
Ondersteunde beveiligingsalgoritmen:	SNMPv3, SSH, SSL/TLS
Reset button:	Ja
Rack-montage:	Ja
Redundante voeding:	Ja
Vermogenstoevoer inclusief:	Ja
Quality of Service (QoS):	Ja
VLAN=ondersteuning:	Ja
Power over Ethernet (PoE):	Ja
Switchingcapaciteit:	176 Gbit/s
MAC-adrestabel:	- entries
10G support:	Ja
Aantal VLANs:	4000
Switch type:	Managed
Aantal basis-switching RJ-45 Ethernet-poorten:	48
Switch-laag:	L3
Type basis-switching RJ-45 Ethernet-poorten:	Gigabit Ethernet (10/100/1000)
DHCP-functies:	DHCP server
IP routing:	Ja
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Code geharmoniseerd systeem (HS):	85176990
Aantal moduleslots SPF+:	4
Rekbevestigingspakket:	Ja
Authenticatie:	MAC-based authentication, Port-based authentication