Kuzco Alonso PD320313 Handleiding

Bekijk gratis de handleiding van Kuzco Alonso PD320313 (1 pagina’s), behorend tot de categorie Verlichting. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.0 sterren uit 3 reviews. Heb je een vraag over Kuzco Alonso PD320313 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

ALSSEMBY TRUONINSCTIS

WD CAISARNINGANS UTON

• Make sure POWER is at the fuse boxCOMPLETELY OFF

• Have your fixture installed by a qualified licensed electrician

• Prepare everything in a clear area

• Wear gloves at all times during this installation

• Read instructions carefully before you start assembly

• Keep this installation sheet for future reference

PD320313

Pendant

TEHNICCRTAL SUPPO

1.855.855.8926

ticsualora.comechnalpport@litighng

NOTICE

•afeansctinedn htor The importnt sagurds and itruonouts li ithis see cannot cve

all ssis cce pobitiatile condons a sindtuonthato may urt st b. Imuundtooersd

thutonndrttormufoThtruonat cai a ceaie acnr cafs st be llwe. odese insctis are

proforourndghomndthtrvided y say afet we hily ecrme atnd a licese, ained

eleciciaall is trnnst ithunit.

•fded bed tnstdtaa d This ixture is esigntoe mounton a correcly ialle sndrdroun

orgonbothroughngbothfrThbomu octa x OR a wiri x wi a plaster ame. e x st be

sece e il. sswaurely me sounted tothtructurofth budingThe crobar ha andrdre

sdld buddirti f tupplie shoue se, ecly mountngthe ixe turtothoute le

may box

make i imly alitpossible ectoorr ctgn the fixture.

CANADA:

USA: 3035 E. Lone Mountain Rd - Las Vegas, NV, 89081

wwligtingcowlora.ah.m

20230628

P:

1.855.855.8926

19054 28th Avenue Surrey - BC V3Z 6M3

1a.

1b.

1c.

1e.

4a.

2b.

2a.

2d.

5a.3a.5b.5c.

Step 1

Remove fixture from its original package.

Step 2

Separate mounting plate (1c) from canopy (2a) by removing canopy screws

(2b).

Step 3

Attach mounting plate (1c) to electrical junction box (1a) using junction box

screws provided (1e) in hardware package.

Step 4

Determine hanging height of fixture by securing rods (2d) to canopy (2a)

and fixture (3a) after feeding fixture wires (LED+ and LED-) through rods.

Step 5

Make proper electrical connections between LED and DC driver, LED-

Negative, LED+ Positive using quick connector provided (See Illustration 1

and refer to diagram on driver).

Step 6

Make proper electrical connections ( to to “N”, blackhot white“L”, neutral

ground GNDto “”) with wire nuts provided in hardware package and (1b)

place driver (4a) in canopy (2a).

Step 7

Secure shade (5a) to fixture (3a), followed by ring (5b) and glass (5c) by

threading clockwise.

Step 8

Attach canopy (2a) to mounting plate (1c) with canopy screws (2b).

You are now ready to enjoy your fixture.

Please Note:

•This Alora LED fixture comes with pre-wired LED module(s)

•Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with

the module could cause permanent damage

•For dimming, an ELV (Electronic Low Voltage) or TRIAC type of dimmer is required

• 120V input

DC

Driver

N

L

-

+

Illustration 1

Low Voltage

Product specificaties