Klipsch Reference RW-5101 Handleiding
Bekijk gratis de handleiding van Klipsch Reference RW-5101 (6 pagina’s), behorend tot de categorie Subwoofer. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 5.0 sterren uit 3 reviews. Heb je een vraag over Klipsch Reference RW-5101 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
I N C E I L I N G L O U D S P E A K E R S-
O
W N E R ’ MS A N U A L A N D A R R A N T YW
3. To install the tilebridge, fold the rail side of the ring back
upon itself using the spring tensioner on the reinforcement ring
to allow insertion into the cutout hole. Once it is inserted into
the cutout hole, release the reinforcement ring such that it
unfolds back to its normal position. Position tilebridge over
cutout hole, and ensure that the tile rails rest on the t-grid struts.
4. The wiring compartment is intended as a termination point
for the audio circuit. Access to this compartment is gained
by removing the terminal cover located on the back of the
speaker. The terminal cover will accept the appropriate
conduit/wire adaptor (provided). Feed wires through
conduit/wire adapter and strip the insulation back approxi-
mately
3
/16". Connect the wires to the appropriate input
terminal. Be sure to observe proper polarity. Replace the
terminal cover and tighten the conduit/wire adapter to secure
the wire.
Caution: When connecting 70V or 100V distributed
line systems, take care to ensure proper terminal
connection. Connection to the low impedance termi-
nal could result in speaker damage, amplifier
damage, or both.
Thank you for purchasing
Klipsch IC-5T and IC-6T in-ceiling speakers.
The IC-5T and IC-6T in-ceiling speakers have been designed for
speech and music reinforcement applications. Unobtrusive, these
loudspeakers are engineered for easy, versatile installation.
The IC-5T and IC-6T feature an internal transformer for 70.7V/100V
distributed-line systems. The transformer taps are selected using a
rotary switch located conveniently under the grille. For applica-
tions where 16 ohm operation is required, the transformer can be
by-passed by using an optional connection located on the back
input terminal.
Before installing your speakers, take a moment to check the con-
tents of the cartons and make sure nothing has been damaged
in transit.
Contents Description Q
UANTITY
Speaker Modules 2
Grilles 2
Reinforcement Ring 2
Rails 4
Cardboard Cutout Template and Paint Mask 1
Screws (Attach Rails to Reinforcement Ring) 4
3/
8"
Adapter Fittings 2
1/
2"
Adapter Fittings 2
Installation Guidelines
The IC-5T and IC-6T include a tilebridge for use when installing
the loudspeaker into suspended ceilings or wherever additional
reinforcement of the ceiling material is required. The tilebridge
and loudspeaker are designed such that installation may be
accomplished where access above the ceiling is not possible
or may be difficult.
Installation
1. The tilebridge is composed of three parts—a reinforcement
ring and two rails. The two rails should be attached to the rein-
forcement ring using the two included screws as shown below.
Caution: Be sure to comply with any and all building codes
in your area.
2. To install your IC-5T or IC-6T, cut out a hole in the ceiling using
either the cardboard cutout template provided with your speak-
ers or consult the measurements below. Pull wiring through hole.
I C - 5 T A N D I C - 6 T
I C - 5 T 8.25"
I C - 6 T 9.75"
5. Insert the speaker into the cutout hole. With a #2 Phillips screw-
driver, tighten the four dog clamps until they are seated securely
against the ceiling surface. Do not overtighten.
6. For installations using the 70/100V input connection, set the
switch on the front panel to the desired tap setting. For applica-
tions where16 Ohm impedance is desired, the switch should be
set to 16 Ohms. Note: The speaker comes from the factory set at
the lowest output setting (highest impedance).
7. The IC-5T and IC-6T feature a ±15 degree swivel tweeter
to aim high frequency sound to a desired location. To aim
sound directly at the listening area, gently adjust the horn to
the desired angle.
8. Using the flat of your hand, insert grille into speaker frame
making sure it is securely seated and flush.
Seismic Tab
A seismic tab, located on the back of the speaker, is used
as a secondary security point. Some construction codes
may require its use. To utilize the seismic tab, run a support
wire from a secure point in the ceiling and attach it to the
tab. Be sure to consult the construction codes in your area.
Klipsch recommends the use of this tab in all installations as
a secondary means of support.
70V
100V
70V
100V
60
IC-5T Transformer tap selectable IC-6T Transformer tap selectable
Product specificaties
| Merk: | Klipsch |
| Categorie: | Subwoofer |
| Model: | Reference RW-5101 |
Heb je hulp nodig?
Als je hulp nodig hebt met Klipsch Reference RW-5101 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Subwoofer Klipsch
16 Juni 2025
1 Mei 2025
19 Februari 2025
19 Februari 2025
8 December 2024
15 November 2024
13 November 2024
13 November 2024
3 April 2024
3 April 2024
Handleiding Subwoofer
- Audison
- Kenwood
- H YANKA
- Genelec
- Elac
- PSB
- Energy
- Extron
- Bose
- Focal
- Ecler
- Monoprice
- Alphasonik
- Polk
- Infinity
Nieuwste handleidingen voor Subwoofer
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025