Klipsch IC-SW-8T Handleiding

Klipsch Subwoofer IC-SW-8T

Lees hieronder de 📖 handleiding in het Nederlandse voor Klipsch IC-SW-8T (6 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6

I C - S W - 8 T I N - C E I L I N G S U B W O O F E R

OW N E R ’SM A N U A L A N D WA R R A N T Y

3. To install the tilebridge, fold the rail side of the ring back

upon itself using the spring tensioner on the reinforcement ring

to allow insertion into the cutout hole. Once it is inserted into

the cutout hole, release the reinforcement ring such that it

unfolds back to its normal position. Position tilebridge over

cutout hole.

4. The wiring compartment is intended as a termination point

for the audio circuit. Access to this compartment is gained by

removing the terminal cover located on the back of the

speaker. The terminal cover will accept the appropriate

conduit/wire adapter (provided). Feed wires through

conduit/wire adapter and connect to the input terminal

according to the desired operation mode. Be sure to observe

proper polarity. Replace the terminal cover and tighten the

conduit/wire adapter to secure the wire.

Caution: When connecting 70V or 100V dist ri b u t e d

line systems, t e care to ensure proper ta k e rm i n a l

connection. Connection to the low impedance t -e rm i

nal could r in speaker damage, ame s u l t p l i f i e r

d a m a g e, or both.

Thank you for purchasing yo u r

K l i p s c h IC-SW-8T i n-cei li ng subw . o o f e r

The IC-SW-8T in-ceiling speaker is designed for music reinforce-

ment applications. Unobtrusive, these loudspeakers are engi-

neered for easy, versatile installation.

The IC-SW-8T features a transformer-less design for 70.7V/100V

distributed-line systems. Some of the benefits of this design are:

Elimintation of transformer saturation at high output levels,

elimination of transformer insertion losses, improved bandwidth

(particularly at low frequencies), and improves power transfer to

the loudspeaker at low frequencies. For applications where 4

ohm mono or 8 ohm stereo operation is required, the mode of

operation can be selected by using an optional connection

located on the back input terminal and by properly setting the

rotary switch located under the grill.

Before installing your speakers take a moment to check the

contents of the cartons and make sure nothing has been

damaged in transit.

Content s Des cription Q U YA N T I T

Speaker Module 1

Grille 1

Reinfor 1cement Ring

Rails 2

Cardboard Cutout Template and Paint Mask 1

Screws (Attach Rails to Reinforcement Ring) 2

3/ 8" Adapter Fittings 1

1/ 2" Adapter Fittings 1

I nstallation Gu id el i nes

The IC-SW-8T includes a tilebridge for use when installing

the loudspeaker into suspended ceilings or wherever additional

reinforcement of the ceiling material is required. The tilebridge

and loudspeaker are designed such that installation may be

accomplished where access above the ceiling is not possible

or may be difficult.

I n s t a l l a t i o n

1. The tilebridge is composed of three parts—a reinforcement ring

and two rails. The two rails should be attached to the

reinforcement ring using the two included screws as shown below.

Caution: Be sure to com y with any and all building codesp l

in your are a .

2. To install your IC-SW-8T cut out a hole in the ceiling using either

the cardboard cutout template provided with your speakers or

consult the measurements below. Pull wiring through hole.

I C - - 8 T S U BS W W O O F E R

I C - S W - 8 T 121/

2" R o u n d

5. Insert the speaker into the cutout hole. With a #2 Phillips screw-

driver, tighten the four dog clamps until they are seated securely

against the ceiling surface. Do not overtighten.

6. For installations using 70v/100v input connection, set the

switch on the front panel to "70V/100V".

For low impedance, stereo applications, the switch should be

set to 8 ohms stereo.

For low impedance, mono applications, the switch should be

set to 4 ohm mono.

In all cases, please make sure the speaker wires are connect-

ed to the appropriate terminal on the back.

7. Using the flat of your hand, insert grille into speaker frame

making sure it is securely seated and flush.

Se i s m i c Ta b

A seismic tab, located on the back of the speaker, is used

as a secondary security point. Some construction codes may

require its use. To utilize the seismic tab, run a support wire

from a secure point in the ceiling and attach it to the tab.

Be sure to consult the construction codes in your area.

Klipsch recommends the use of this tab in all installations as

a secondary means of support.

IC-SW-8T tap selectable

Product specificaties

Merk:	Klipsch
Categorie:	Subwoofer
Model:	IC-SW-8T

Heb je hulp nodig?

Als je hulp nodig hebt met Klipsch IC-SW-8T stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Subwoofer Klipsch

Klipsch Reference Premiere RP-1200SW Handleiding

3 April 2024

Klipsch Reference Premiere RP-1000SW Handleiding

3 April 2024

Klipsch PRO-1000SW Handleiding

27 Maart 2024

Klipsch R-120SWi Handleiding

27 Augustus 2023

Klipsch LF-10 Handleiding

12 Juni 2023

Klipsch KD-10SW Handleiding

14 Mei 2023

Klipsch Reference Sub Handleiding

10 Mei 2023

Klipsch Reference Premiere RP-1600SW Handleiding

30 April 2023

Klipsch Reference Premiere RP-1400SW Handleiding

25 April 2023

Klipsch THX-1200-SW Handleiding

23 April 2023

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

RCF S 19 Handleiding

10 April 2024

RCF S 29 Handleiding

10 April 2024

KEF KC92 Handleiding

6 April 2024

Velodyne Deep Waves 10 Handleiding

27 Maart 2024

Totem KIN Sub Handleiding

27 Maart 2024

Velodyne Deep Waves 12 Handleiding

27 Maart 2024

Kanto SUB8V Handleiding

27 Maart 2024

Canton Sub 10.4 Handleiding

26 Maart 2024

Canton Sub 12.4 Handleiding

26 Maart 2024

Audiotec Fischer Match UP W8BMW-S Handleiding

25 Maart 2024