Klipsch IC-400-T Handleiding

Klipsch Speaker IC-400-T

Lees hieronder de 📖 handleiding in het Nederlandse voor Klipsch IC-400-T (6 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6

I N - C E I L I N G L O U D S P E A K E R S

O ’ MW N E R S A N U A L A N D WA R R A N T Y

I C - 4 0 0 - T , I C - 5 2 5 - T & I C - 6 5 0 - T

3. To install the tilebridge, fold the rail side of the ring back

upon itself using the spring tensioner on the reinforcement ring

to allow insertion into the cutout hole. Once it is inserted into

the cutout hole, release the reinforcement ring such that it

unfolds back to its normal position. Position tilebridge over

cutout hole, and insure that the tile rails rest on the t-grid struts.

4. The wiring compartment is intended as a termination point

for the audio circuit. Access to this compartment is gained by

removing the terminal cover located on the back of the

speaker. The terminal cover will accept the appropriate

conduit/wire adapter (provided). Feed wires through

conduit/wire adapter and connect to the input terminal

according to the desired operation mode. Be sure to observe

proper polarity. Replace the terminal cover and tighten the

conduit/wire adapter to secure the wire.

Caution: When connecting 70V or 100V distributed

line systems, take care to ensure proper terminal

connection. Connection to the low impedance termi-

nal could result in speaker damage, amplifier

damage, or both.

Thank you for purchasi ng your Klipsch IC-400-T,

IC-525-T or IC-650-T in-ceiling speakers.

The IC-400-T, IC-525-T and IC-650-T in-ceiling speakers have been

designed for music reinforcement applications. Unobtrusive,

these loudspeakers are engineered for easy, versatile installation.

The IC-400-T, IC-525-T and IC-650-T feature an internal transformer

for 70V/100V distributed-line systems. The transformer taps are

selected using a rotary switch located conveniently under the

grille. For applications where 8 ohm operation is required, the

transformer can be by-passed by using an optional connection

located on the back input terminal and selectin 8 Ohm on the

front switch.

Before installing your speakers take a moment to check the

contents of the cartons and make sure nothing has been

damaged in transit.

Contents Description QUANTIT Y

Speaker Modules 2

Grille 2

Reinforcement Ring 2

Rails 4

Cardboard Cutout Template and Paint Mask 2

Screws (Attach Rails to Reinforcement Ring) 8

3/4" Adapter Fittings 2

Installation Guidelines

The IC-400-T, IC-525-T and IC-650-T include a tilebridge for use

when installing the loudspeaker into suspended ceilings or wher-

ever additional reinforcement of the ceiling material is required.

The tilebridge and loudspeaker are designed such that installa-

tion may be accomplished where access above the ceiling is

not possible or may be difficult.

Installation

1. The tilebridge is composed of three parts—a reinforcement ring

and two rails. The two rails should be attached to the reinforce-

ment ring using the four included screws as shown below.

Caution: Be sure to comply with any and all building codes

in your area.

2. To install your IC-400-T, IC-525-T or IC-650-T cut out a hole in the

ceiling using either the cardboard cutout template provided with

your speakers or consult the measurements below. Pull wiring

through hole.

I C - 4 0 0 - T , I C - 5 2 5 - T & I C - 6 5 0 - T

I C - 4 0 0 - T , I C - 5 2 5 - T 9.125 " R o u n d

I C - 6 5 0 - T " R o u n d10.125

5. Insert the speaker into the cutout hole. With a #2 Phillips screw-

driver, tighten the four dog clamps until they are seated securely

against the ceiling surface. Do not overtighten.

6. For installations using 70v/100v input connection, set the switch

on the front panel to the desired setting. For applications where 8

Ohm impedance is desired, the switch should be set to 8 Ohms.

Note: The speaker comes from the factory set at the lowest

output setting (highest impedance).

7. Using the flat of your hand, insert grille into speaker frame

making sure it is securely seated and flush.

Se i s m i c Tab

A seismic tab, located on the back of the speaker, is used

as a secondary security point. Some construction codes may

require its use. To utilize the seismic tab, run a support wire

from a secure point in the ceiling and attach it to the tab.

Be sure to consult the construction codes in your area.

Klipsch recommends the use of this tab in all installations as

a secondary means of support.

15W

7.5W

15W

1.875W

3.75W

7.5W

70V

100V

IC-400-T tap selectable

30W

7.5W

15W

30W

3.75W

7.5W

15W

70V

100V

IC-525-T tap selectable

60W

15W

30W

7.5W

15W

30W

70V

100V

IC-650-T tap selectable

Product specificaties

Merk:	Klipsch
Categorie:	Speaker
Model:	IC-400-T
Kleur van het product:	Zwart
Gewicht:	2835 g
Breedte:	273.1 mm
Diepte:	190.5 mm
Hoogte:	273.1 mm
Installatie compartiment afmetingen(WxDxH):	231.8 x 185.8 x 231.8 mm
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	50 W
Equalizer-instellingen:	Nee
Impedantie:	8 Ohm
Geschikt voor buitengebruik:	Nee
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Plafond-montage
Aantal drivers:	1
Woofer:	Ja
Diameter driver subwoofer (imperiaal):	1 "
Frequentiebereik:	70 - 20000 Hz
Gevoeligheid:	86 dB
Versterkeraansluiting (binding post):	Ja
Diameter woofer:	5 "
Driver cone material:	Titanium