Kichler 49669WZC Ashland Lamp Handleiding

Kichler Lampen 49669WZC Ashland Lamp

Lees hieronder de 📖 handleiding in het Nederlandse voor Kichler 49669WZC Ashland Lamp (1 pagina's) in de categorie Lampen. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
6) Connecter les ïŹls (connecteurs non fournis). Se reporter au
tableau ci-dessous pour faire les connexions.
7) Pousser le luminaire vers le plafond en passant soigneusement
les vis de montage par les trous dans le cache.
8) Fixer le luminaire au plafond Ă  l’aide des boutons moletĂ©s.
9) Installer l’ampoule recommandĂ©e.
10) Soulever le verre jusqu’au luminaire. Placer le verre entre les
tiges. Passer le trou en haut du verre sur l’ampoule et la
douille. Installer le bord supérieur du verre dans le cache.
11) Soulever le capuchon infĂ©rieur jusqu’au luminaire. Passer
les petits trous le long du bord du capuchon inférieur sur les
goujons ïŹletĂ©s situĂ©s courts sur les extrĂ©mitĂ©s de chaque
tige. Serrer les capuchons ïŹletĂ©e sur des goujons ïŹletĂ©s
dépassant du fond du capuchon inférieur. Resserrer les
capuchons ïŹletĂ©s pour ïŹxer le verre. (NE PAS serrer avec
excĂšs).
1) With rod positioned so the longer threaded stud on the rod
is on top of the rod, pass long threaded stud on end of rod
up through hole in canopy. Thread ïŹnial on to end of rod
protruding from top of canopy.
2) Repeat step 1 for remaining rods.
3) TURN OFF POWER.
Before you start, NEVER attempt any work IMPORTANT:
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the ïŹxture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the ïŹxture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
4) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
5) Attach mounting strap to outlet box. (Screws not provided)
Mounting strap can be adjusted to suit position of ïŹxture.
6) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
7) Push ïŹxture to ceiling, carefully passing mounting screws
through holes.
8) Screw threaded balls onto mounting screws. Tighten
threaded balls to secure ïŹxture to ceiling.
9) Insert recommended bulb.
10) Raise glass up to ïŹxture. Fit glass in between rods. Pass
hole in top of glass over bulb and socket. Fit top edge of
glass inside canopy.
11) Raise bottom cap up to ïŹxture. Pass small holes along edge
of bottom cap over short threaded studs on ends of each
rod. Screw threaded caps onto threaded studs protruding
from bottom of bottom cap. Tighten threaded caps to
secure glass in place. (DO NOT over tighten.)
1) Avec la tige positionnĂ©e de maniĂšre Ă  ce que le goujon ïŹletĂ©
le plus long soit sur le dessus de la tige, passer le long
goujon ïŹletĂ© sur l’extrĂ©mitĂ© de la tige par le trou du cache.
Serrer l’ornement sur l’extrĂ©mitĂ© de la tige sortant du dessus
du cache.
2) RĂ©pĂ©ter l’étape 1 pour les autres tiges.
3) COUPER LE COURANT.
TOUJOURS couper l’électricitĂ© avant de IMPORTANT:
commencer le travail.
a) Localiser le coffret Ă  fusibles ou le disjoncteur du
domicile. Mettre l’interrupteur principal en position d’ArrĂȘt.
b) DĂ©visser le ou les fusibles (ou mettre le disjoncteur sur
ArrĂȘt) qui contrĂŽlent l’alimentation vers le luminaire ou la
piÚce dans laquelle le travail est effectué.
c) Mettre l’interrupteur mural en position d’ArrĂȘt. Si le luminaire
Ă  remplacer est dotĂ© d’un interrupteur ou d’une chaĂźne
connectĂ©e Ă  l‘interrupteur, placer ces Ă©lĂ©ments en
position d’ArrĂȘt.
4) Trouver les trous ïŹletĂ©s appropriĂ©s sur la barrette de
montage. Vissez les vis de montage dans les trous ïŹletĂ©s.
5) Visser la barrette de montage Ă  la boite de jonction. (Vis non
fournies). La barrette de montage peut etre ajustée pour
convenir à la position de l’applique.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.) Neutral Wire
Connecter le fil noir ou
rouge de la boite Connecter le fil blanc de la boĂźte
A Noir A Blanc
*Au cordon parallÚle (rond et lisse) *Au cordon parallele (à angles droits el strié)
Au bransparent, doré, marron, ou
noir sans fil distinctif
Au transparent, doré, marron, ou
noir avec un til distinctif
Fil isolé (sauf fil vert) avec
conducteur en cuivre
Fil isolé (sauf fil vert) avec
conducteur en argent
*Remarque: Avec emploi d’un fil parallĂ©le
(SPT I et SPT II). Le fil neutre est ĂĄ angles
droits ou striĂ© et l’autre fil doit Ă©tre rond ou
lisse (Voir le schéma). Fil Neutre
Date Issued: 10/16/15 IS-49669-CB
CANOPY
CACHE
THREADED BALL
BOULE FILETÉ
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
MOUNTING STRAP
SUPPORT DE MONTAGE
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
GLASS
VERRE
BOTTOM CAP
CAPUCHON INFÉRIEUR
THREADED CAP
CAPUCHON FILETÉ
FINIAL
ORNEMENT
ROD
TIGE


Product specificaties

Merk: Kichler
Categorie: Lampen
Model: 49669WZC Ashland Lamp

Heb je hulp nodig?

Als je hulp nodig hebt met Kichler 49669WZC Ashland Lamp stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Lampen Kichler

Handleiding Lampen

Nieuwste handleidingen voor Lampen