Kichler 43848NILED27T Handleiding

Bekijk gratis de handleiding van Kichler 43848NILED27T (2 pagina’s), behorend tot de categorie Verlichting. Deze gids werd als nuttig beoordeeld door 4 mensen. Heb je een vraag over Kichler 43848NILED27T of wil je andere gebruikers van dit product iets vragen? Stel een vraag

WARNING:

• This fixture is intended for installation in accordance with the

National Electric Code (NEC) and all local code specifications.

• Supply wires are not intended for use through or concealed

behind walls, floors, or ceilings.

• The LED light output is strong enough to injure human eyes.

Precautions must be taken to prevent looking directly at LED’s

with unaided eyes for more than a few seconds.

DIMMING: This LED fixture is compatible with electronic low

voltage dimmers only.

1) Read and understand all instructions and illustrations completely

before proceeding with assembly and installation of fixture.

2) If you have any doubts about how to install this fixture, or if

the fixture fails to operate completely, please contact a

qualified electrician.

3) All parts must be used as indicated in the instructions. Do not

substitute any parts, leave parts out, or use any parts that are

worn or broken. Failure to obey this instruction could invalidate

the UL listing, C.S.A. certification, and/or ETL listing of this fixture.

4) Fixture is to be connected to a single branch circuit.

1) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your home.

Place the main power switch in the “OFF” position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the fixture or room that

you are working on.

c) Place the wall switch in the “OFF” position. If the fixture to

be replaced has a switch or pull chain, place those in the

“OFF” position.

2) Grounding instructions: (See Illus. A or B).

A) On fixtures where mounting strap is provided with a hole

and two raise dimples. Wrap ground wire from outlet box

around green ground screw, and thread into hole.

B) On fixtures where a cupped washer is provided. Put ground

wire from outlet box under cupped washer and green

ground screw and thread screw into hole in mounting strap.

If fixture is provided with ground wire. Connect fixture ground

wire to outlet box ground wire with wire connector, (not provided)

after following the above steps. Never connect ground wire to

black or white power supply wires.

GREEN GROUND

SCREW

CUPPED

WASHER

A

B

OUTLETBOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

(NOTPROVIDED)

OUTLETBOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

BlackWhite

*Parallel cord (round & smooth)*Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Date Issued: 8/28/15IS-43846LED-US

LENS COVER

PROTECCIÓN

DEL LENTE

FIXTURE

ARTEFACTO

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

SCREW

TORNILLO

3) Make wire connections. Reference chart below for correct

connections and wire accordingly.

4) Mounting surface should be clean, dry, flat and 1/4” larger

than the fixture housing surface.

5) Twist lens cover counter-clockwise to remove from fixture.

6) Place fixture over outlet box, carefully passing fixture mounting

screws through clearance holes in canopy.

7) Any gaps in the mounting surface exceeding 3/16” should be

corrected as required.

8) Replace the lens cover back on the disk light by lining up tabs

on lens and turning to lock in place.

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.

VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener-

ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Product specificaties