Kathrein UAS 582 Handleiding

Kathrein Niet gecategoriseerd UAS 582

Bekijk gratis de handleiding van Kathrein UAS 582 (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 55 mensen en kreeg gemiddeld 4.1 sterren uit 28 reviews. Heb je een vraag over Kathrein UAS 582 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/8

1 / 8

Universal Wideband feed system 10,70-12,75 GHz

About this Guide

This document is part of the product.

►Read these instructions for use before the initial use of

the antenna set.

►Perform all operating steps described in the manuals

in the speciﬁ ed sequence.

For the most up-to-date version of this document, go to

www.kathrein-ds.com.

Keep these instructions for future reference.

Pass them on to any new owners when

selling or transferring the unit.

Features

■Universal Wideband feed system with 2 outputs

■Suitable for Kathrein o set parabolic antennas, type CAS.. (60, 80, 90, 120 cm Ø)

■For reception of satellites in the Ku band, such as ASTRA, EUTELSAT and TürkSat

■50% less cable material required: To receive one satellite, only two cables from the LNB to the wideband multiswitch

are required, with Multifeed, two satellites can be received with just four cables

■Energy saving - only max. 1,2 W power consumption

■The feed system complies with ASTRA speciﬁ cations for universal Wideband feed systems

■Power supply via coax cable

■Multifeed-suitable due to compact design

■Full protection of LNB and cable connections in a ventilated housing, protection category IP 54

■UAS 582

■2 x F-type plug

■Azimut-/elevations table

■Instructions for use

Transport and Storage

►Transport and store the device in its original packaging.

►Make sure there is no water condensation build-up.

Intended Use

►The device described is designed solely for the installation of satellite receiver systems and may only be installed by

trained specialist personnel.

►The UAS 582 feed system may only be mounted to the listed Kathrein parabolic antennas.

►If it is used in any other way or if the provisions of this document are disregarded, the guarantee and warranty will

become void.

►The manufacturer is not liable for accidents caused by the user on the opened device.

►Unauthorized opening and repair attempts lead to the loss of the warranty claim.

Scope of Delivery

UAS 582 20110032

2 / 8

Safety Instructions

The UAS 582 feed system may only be mounted to the listed Kathrein parabolic antennas. The feed

system is subject to the same safety and danger warnings as listed in the instructions for using of

fset parabolic antennas. Please follow these instructions at all times, as otherwise you or other

people may be exposed to danger (electric shock through overhead lines, risk of falling down, falling

parts, thunderstorm etc.).

Mounting and Connection of the feed system

Fixing the feed system (Fig. 1)

1. Position the feed system as desired on the multifeed

plate at the end of the bracket (see antenna instruc-

tions)

2. Fasten the feed system on the front part using the

Allen wrench (torque: 4.5 Nm).

All fastening and tightening can be e ected

with a Allen wrench (SW4).

Hier ansetzen

= 4,5 Nm

Setting the polarisation (Fig. 2)

See the value in the table Tab. 1,S.5 for the polarisa-

tion setting.

If the value di ers from the pre-set 0°, proceed as follows:

1. Loosen both Allen screws (S).

2. Turn the feed system to set the reference mark to the

value given in the polarisation pre-setting table.

3. Tighten the Allen screws (S) evenly, alternating

between both.

Torque: max. 4.5 Nm

Polarisation 0°

Polarisation +15°

Polarisation -15°

Allen screw (S)

Fig. 1: Fixing the feed system

Fig. 2: Setting the polarisation

3 / 8

Cable connection

1. Loosen the Allen screws (S) at the rear end of the

cover until the cover can be unlocked by applying light

downward pressure ; remove cover .① ②

If the feed system is not only exchanged but

a new antenna system is being installed,

proceed ﬁ rst as described in the section

“Aligning the satellite reception system” and

then return to “Cable connection”.

2. Mount the supplied F-type plug onto the Kathrein

cable types LCD 90, LCD 111A+, LCD 115A+ oder LCD

120A+ montieren and connect to the LNB (see Fig. 4).

3. When connecting the matrix and the LNB, make sure

the correct output is assigned (mark cables if neces-

sary).

4. It is important to ensure that the bending radius of the

corresponding cable is not undershot.

5. Lead the connected cable forwards and insert side-

ways into the cable fastening (see close-up in Fig. 5

below).

6. Slide on the cover until it ﬁ ts into the groove and locks

in the bottom section. Tighten Allen screw (S).

Allen screw (S)

①

②

Fig. 3: Remove cover

6,5 mm

ﬂush

Fig. 4: Plug mounting

2 x

Fig. 5: Cable connection

Product specificaties

Merk:	Kathrein
Categorie:	Niet gecategoriseerd
Model:	UAS 582
Kleur van het product:	Grijs
Gewicht:	800 g
Breedte:	44 mm
Diepte:	135 mm
Hoogte:	235 mm
Breedte verpakking:	65 mm
Diepte verpakking:	185 mm
Hoogte verpakking:	295 mm
Land van herkomst:	Duitsland
Aantal RF-poorten:	2
Aantal:	1
Stroomverbruik:	1200 mA
RF aansluitingstype:	F
Output impedance:	75 Ohm
Input frequentiebereik:	10.7 - 12.75 GHz
Output frequentiebereik:	300 - 2350 MHz
Oscillatie frequentie:	10.4
Winst:	50 dB
X-polarisatie:	22 dB
Lokale oscillator (LO) ruisfase (10 kHz):	95 dBc/Hz