Jung 4008 TSM Handleiding
Jung
Niet gecategoriseerd
4008 TSM
Bekijk gratis de handleiding van Jung 4008 TSM (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 5.0 sterren uit 1.5 reviews. Heb je een vraag over Jung 4008 TSM of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
Page 1
0024015020 12.10.2012
Push-button sensor module
Ref.-no.: 4008 TSM
Safety instructions
Caution! Electrical devices may only be installed and tted by electrically skilled persons.
Non-compliance with the installation information could cause damage to the device, re or other hazards.
Connect the push-button sensor module exclusively to the universal relay or dimming station (no mains potential!).
To fasten radio to the supporting ring, only use the enclosed plastic screws.
These instructions are a component part of the product and must remain with the end customer.
Correct use
• Operation of consumers, e.g. light on/off, dimming, blinds/shutters up/down, calling up and saving light scenes etc.
• Connection to relay station or dimming station
• Installation in appliance box according to DIN 49073
Product characteristics
• 8 channels of the relay and dimming station can be controlled: switching, contact, dimming, blind/shutter.
• 16 channels for stations connected in parallel in conjunction with the push-button sensor expansion module.
• All channels of the stations can be connected in the state as delivered.
• Central function: all selected channels of the stations are controlled centrally
• Light scenes: up to 4 light scenes can be freely congured.
• Buttons can be congured corresponding to the cover kit.
• Programming without additional aids
• Free assignment of the buttons to the channels
• Red LED as status indicator (can be switched off)
• Blue orientation light (can be switched off)
• Feedback of switching states on all connected push-button sensor modules and sensor modules
• Up to 4 push-button sensor modules with up to 4 push-button sensor expansion modules can be connected to a single relay station (appli-
cation e.g. in two-way circuits or cross connections)
• Cloning of push-button sensor modules: transmitting the button assignment of a push-button sensor module to other push-button sensor
modules (application e.g. in changeover or cross connections)
• Push-button sensor modules and push-button sensor modules with expansion module can be cloned
• Easy installation using 2-wire cable
• Covers can be labelled using the laser labelling tool on the Internet under www.jung-lasern.de
• Operation
• Each button can be operated over its entire surface or top/bottom, depending on the programming. The function depends on the setting of
the station.
• Switching / momentary contact: press button briey.
• Move blind/shutter: press and hold button.
• Stop or adjust blind/shutter: press button briey
• Dimming: press and hold button
Structure of the device
Bild 1: Installation
(1) Supporting ring
(2) Frame
(3) Adapter frame
(4) Push-button sensor module
(5) Locking screw
(6) Button set
(7) Connecting terminal
(8) Box screws
Page 2
0024015020 12.10.2012
Information for electrically skilled persons
Installation and electrical connection
DANGER!
Electric shock from touching live parts in the installation environment.
An electric shock can be fatal.
Before working on the device, disconnect the power and cover live parts in the area!
Snapping on the adapter frame
An adapter frame is required depending on the switch range.
The adapter frame for the series LS is pre-mounted.
• Snap adapter frame (3) in the right orientation from the front onto the module (8) (Figure 2). Observe the label „TOP“.
Connection
Attention!
Connect the push-button sensor module exclusively to the universal stations.
Installing and connecting the device
(8)
(13)
(4)
(5)
(5)
(11)
(12)
(8)
(10)
(9)
Bild 2: Installation with expansion module
(9) Connecting cable TSEM
(10) Plug-in position
(11) Push-button sensor expansion module
(12) Frame
(13) Double supporting ring
Supporting ring side A for A range, CD range
and at design.
Supporting ring side B for LS range.
When using the push-button sensor expansion module (Figure 2): vertical installation is preferred. Use the double supporting ring (13). For
installation to a ush-mounted box only, countersink the lower screws in the wall, e.g. with bore ø 6 x 10 mm. Use supporting ring as template.
DANGER!
When installing with 230 V devices under a common cover, e.g. socket outlets, there is a danger of electric shock in the event
of an error!
An electric shock can be fatal.
Do not install any 230 V devices in combination with a push-button sensor expansion module under a common cover!
• Install supporting ring (1) or (13) in the right orientation on an appliance box. Observe the label „TOP“; label A or B forwards.
Use only the supplied box screws (8).
• Insert frame (2) onto the supporting ring.
• Preferred installation position of push-button sensor expansion module (15) is below.
Guide connecting cable (16) between supporting ring and intermediate web.
• Push-button sensor expansion module: insert connecting cable (16) in the right orientation in the plug-in position (17) in the push-button
sensor module.
Do not pinch the connecting cable.
• Connect push-button sensor module (4) with connecting terminal (7) to the station and insert onto the supporting ring.
• Fasten the push-button sensor module(s) to the supporting ring using the enclosed plastic screws (5).
Only tighten the plastic screws lightly.
Page 3
0024015020 12.10.2012
Start-up
The push-button sensor module is ready for operation immediately after it is connected to the stations (initial commissioning).
Push-button
sensor module
Relay station Dimming
station
Button 1 top Output 1 Output 1 on/
brighter
Button 1 bottom Output 2 Output 1 off/
darker
Button 2 top Output 3 Output 2
on/brighter
etc...
When a push-button sensor module is operated with a push-button sensor expansion module on a single station, the push-button sensor expan-
sion module does not have any function in the state as delivered.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Bild 3: Button assignment in state as delivered without and with push-button sensor expansion module.
Grouping
1
16
13
16
1 4
1
14
3
16
1 2
1413 15
3 4
16
11 3
9
14 16
6
2
5 6
1413
9 10
15
3 4
16
9
14
1
6
11
16
3
8
1 2
5 6
1413
9 10
3 4
7 8
1615
11 12
Bild 4: Button conguration for entire surface or top/bottom mode, for 1gang, 2gang, 3gang and 4gang covers.
Product specificaties
| Merk: | Jung |
| Categorie: | Niet gecategoriseerd |
| Model: | 4008 TSM |
Heb je hulp nodig?
Als je hulp nodig hebt met Jung 4008 TSM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Jung
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
Handleiding Niet gecategoriseerd
- Vivax
- MQ
- Aqua-Vu
- MSI
- YISHU
- KJB Security Products
- Piet Boon
- Fiber Novelty
- Aroma
- Eissound
- Promate
- Weil
- Sifflus
- Zeiss
- Bauhn
Nieuwste handleidingen voor Niet gecategoriseerd
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025
14 Juli 2025