Jung RCD2044 Handleiding
Jung
Niet gecategoriseerd
RCD2044
Bekijk gratis de handleiding van Jung RCD2044 (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.5 sterren uit 3 reviews. Heb je een vraag over Jung RCD2044 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
KNX Room Controller Universal
Ref.-no.: RCD 20xx
Operating Instructions
Room Controller Universal
1. System information
This unit is a product of the KNX/EIB-System and corresponds to the
EIBA Guidelines. Detailed technical knowledge acquired in KNX training
courses is a prerequisite for the understanding of the system. The
functions of the device are software-dependent. Planning, installation and
commissioning of the device are effected with the help of EIBA-certified
software (ETS 2 version 1.2a or 1.3 or ETS3). For the RCD-software and
technical descriptions please refer to the internet at www.jung.de oering
up-to-date information.
2. Funktion
The KNX/EIB room controller RCD 20xx combines the functionality of an
universal push button and a room temperature sensor. Beside it the
device indicates the status and the parameter of the continuous action
regulator and is equipped with a fan coil application. The actual fan coil
status is also indicated on the illuminated LCD.
Functional range of the push button part
Each button can be programmed separately:
switching • toggling • dimming (single level or two level dimming) •
shutter/blind control (single level or two level control) • value transmitter •
Brightness value transmitter (0 - 1500 Lux) • Light mood recall with and
without memory • Saving light mood • presence push-button for
thermostat • Set temperature offset adjustment • fan levels • block
function • Status LED for each push button with separate objects
Functional range of the temperature sensor part
The temperature sensor is used to control single room temperature. It is
possible to choose a steady control or a two step control application to
control an KNX/EIB switching or heating actor in connection with an
electrothermic device.
Depending on settings of continuous PI control, switching PI control, two
step control or switching two step control • heating and/or cooling with
manual or automatic switching and collective or parted actor outputs
possible two step heating and cooling operation • ve operation modes
with the respective set value • comfort extension or operation mode
changes through presence push button • freeze/heating protection •
Stand: Apr-08 825 548 03
KNX Room Controller Universal
Ref.-no.: RCD 20xx
temperature drop detection • external controlled objects for comfort
mode, freeze and heat protection and control lock-out • control status, set
value and actual value through KNX/EIB accessible • set value
adjustment of max. ± 6 K through push button and software possible •
lock-out of the control elements to protect against unauthorised
adjustments
3. Installation
Attention! Electrical equipment must be installed and fitted only by
qualified electricians and in observance of the applicable accident
prevention regulations. Any non-observance of the fitting
instructions may cause fire or other hazards.
4. Connection and mounting of the RCD 20xx
The RCD has an integrated bus coupling unit. It is connected with a bus
terminal connection block (2).
• 1.Metal plate (1) to be mounted on one or two vertically arranged
wall boxes. When using only one box, the lower part has to be
screwed via the fixing holes (10).
• Attach the frame (3) to the RCD.
• Connect the bus terminal (2) at the back side.
• Attach the RCD (4) and frame (3) on the metal plate (1). Notice:
Do not pen in the terminal wires.
• Screw on the fixing screw (8).
• Remove the protection foil (5) from the display.
• Put on the transparent cover (7) with the inscription foil (6) to the
RCD.
The programming mode is activated by pushing the programming button
(9).
Note: Do not mount the device next to heat sources due to the influence
of the integrated temperature sensor.
2
KNX Room Controller Universal
Ref.-no.: RCD 20xx
5. Operation
The room controller has two operation modes.
Operation level 1
In operation level 1 all push buttons have the parameterised function. The
LCD can display either the actual temperature, the actual set temperature
of the continuous action regulator, the actual time, the actual date and an
external value (integral EIS5-value).
In the default setting, the push button
and right side of the display
serve the presence and the
set-temperature adjustment.
According to the needs, the default setting can be changed to the full
function of an universal push button.
Switching-over between
comfort-temperature
and
standby-temperature
Adjusting the comfort-temperature:
Left push-button: lower the comfort-temperature
Right push-button: raise the comfort-temperature
Operation level 2
Via long push button action
(> 3s) of push button 1+2 the device
switches over to the 2nd operation level.
In this operation level the set-values of
the continuous regulator and the contrast
of the LC-Display can be adjusted.
or
3
Product specificaties
| Merk: | Jung |
| Categorie: | Niet gecategoriseerd |
| Model: | RCD2044 |
Heb je hulp nodig?
Als je hulp nodig hebt met Jung RCD2044 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Jung
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
Handleiding Niet gecategoriseerd
- HeartSine
- Wacker Neuson
- Gustavsberg
- Heitech
- Möhlenhoff
- Zendure
- Ashdown Engineering
- Musicmate
- City Theatrical
- Telestar
- Lasita Maja
- Analog Way
- Nite Ize
- Whitestone
- MAAS
Nieuwste handleidingen voor Niet gecategoriseerd
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025