Juki LU2-4410_4430-B1T-CS Handleiding

Juki Naaimachine LU2-4410_4430-B1T-CS

Lees hieronder de 📖 handleiding in het Nederlandse voor Juki LU2-4410_4430-B1T-CS (28 pagina's) in de categorie Naaimachine. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/28
A181E09 P019
LOCKSTITCH COMPOUND-FEED
AUTOMATIC UNDERTRIMMER
INDUSTRIAL SEWING MACHINES
MODEL
INSTRUCTION MANUAL
LU2-4410-B1T- CS
(Single-Needle)
LU2-4430-B1T (Double-Needle)
PRECAUTION BEFORE STARTING OPERATION
1 Safety Precautions
1 . Whenturningthepoweron,keepyourhandsandngersawayfromtheareaaround/
undertheneedleandtheareaaroundthepulley.
2 . Thepowermustbeturnedo󱐯whenthemachineisnotused,orwhentheoperator
leaveshis/herseat.
3 . Thepowermustbeturnedo󱐯beforetiltingthemachinehead,installingorremoving
the“V”belt,adjustingthemachine,orreplacingparts.
4 . Avoidplacingngers,hairs,obstacles,etc.nearthepulley,V”belt,bobbinwinder
wheel,ormotorwhenthemachineisinoperation.Injurycouldresult.
5 . Don’tputngersintothethreadtake-uplevercover,around/undertheneedle,or
pulleywhenthemachineisinoperation.
6 . Ifthebeltcover,thengerguard,and/ortheeyeguardareinstalled,don’toperate
themachinewithoutthesesafetydevices.
2 Precaution before Starting Operation
1 . Ifthemachine’soilpanhasanoilsump,neveroperatethemachinewithoutllingoil
init.
2 . Ifthemachineislubricatedbyadropoiler,neveroperatethemachinewithout
lubricating.
3 . Whenanewsewingmachineisoperated,verifytherotationaldirectionofthepulley
withthepoweron.
 (Thepulleyshouldrotatecounterclockwisewhenviewedfromthepulley.)
4 . Verifyvoltageand(singleorthree)phaseindicatedonthenameplateofthemotor.
3 Precaution for Operating Conditions
1 . Avoidusingthemachineatabnormallyhightemperature(35℃orhigher)orlow
temperature(5℃orlower).Otherwise,machinefailuremayresult.
2 . Avoidusingthemachineindustyconditions.
3 . Avoidusingthemachineinconditionslledwithalotofelectricnoisessuchashigh-
frequencywelders.
INTRODUCTION
Thank you very much for purchasing industrial sewing machine.
Please read this instruction manual before operating the sewing machine. Please read also
“Safety Manual”, “Instruction manual for LIMISERVO” and operate the sewing machine
correctly and safely.
CONTENTS
PREPARATION FOR OPERATION ……………………………………………… 1
1Adjustmentoftheneedlestoppingposition……………………………………… 1
USAGE PRECAUTION ……………………………………………… 2
1Lubrication(1)………………………………………………………………………… 2
2Lubrication(2)………………………………………………………………………… 2
3Lubricationcondition………………………………………………………………… 3
4Adjustmentoflubricationtotherotatinghook ………………………………… 3
5Precautionforthebuilt-intypedetector ………………………………………… 3
6Installationofthebeltcover ……………………………………………………… 3
7Precautiononoperation …………………………………………………………… 3
HOW TO USE ……………………………………………… 4
1Installationofneedles ……………………………………………………………… 4
2Windingofthebobbinthread……………………………………………………… 4
3Selectionofthethread……………………………………………………………… 5
4Threadingofneedlethreads ……………………………………………………… 5
5Adjustmentoffeed(stitch)lengthandbackstitch……………………………… 6
6Settingofbobbins …………………………………………………………………… 6
7Threadingofbobbinthreads ……………………………………………………… 7
8Adjustmentofbobbinthreadstension…………………………………………… 7
9Balanceofthreadstension ………………………………………………………… 7
:Adjustmentofneedlethreadstension …………………………………………… 7
AAdjustmentofthepresserfootpressure………………………………………… 7
BTimingbetweentherotatinghookmotionandtheneedlemotion…………… 8
CAdjustmentofthefeeddogheight ……………………………………………… 9
D
Relationshipbetweentherotatinghookmotionandthethreadtake-uplevermotion
… 10
ERelationshipbetweentherotatinghookmotionandtheopenermotion …… 10
FRelationshipbetweentheneedlemotionandthefeeddogmotion…………… 11
GSafetyclutch …………………………………………………………………………12
HAdjustmentofupperfeedlength(needleside) ………………………………… 13
IAdjustmentofforward/backwardfeedlength ………………………………… 13
JAdjustmentoftheoutsidepresserfootandtheinsidepresserfoot ………… 13
KInstallationofthemovableknife…………………………………………………… 15
LInstallationpositionofthethreadtrimmercam………………………………… 16
MAdjustmentofthethreadtrimmercam ………………………………………… 16
NAdjustmentofthethreadtensionreleasing……………………………………… 17
O
Adjustmentofmeshingpressurebetweenthemovableknifeandthexedknife
… 18
PSharpeningofthexedknife ……………………………………………………… 18
Q
Adjustmentofthethreadtrimmerwithchangingthewidthbetweenneedles
… 19
RInstallationofthesolenoidarm …………………………………………………… 20
SRemovalprocedureofthehook…………………………………………………… 20
SPECIFICATIONS ……………………………………………… 21


Product specificaties

Merk: Juki
Categorie: Naaimachine
Model: LU2-4410_4430-B1T-CS

Heb je hulp nodig?

Als je hulp nodig hebt met Juki LU2-4410_4430-B1T-CS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Naaimachine Juki

Handleiding Naaimachine

Nieuwste handleidingen voor Naaimachine