Juki AW-3S Handleiding

Juki Naaimachine AW-3S

Lees hieronder de 📖 handleiding in het Nederlandse voor Juki AW-3S (47 pagina's) in de categorie Naaimachine. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/47

INSTRUCTION MANUAL

AW-3S

CONTENTS

1. GENERAL ............................................................................................... 1

1-1. Specications of AW-3....................................................................................................... 1

1-2. Conguration...................................................................................................................... 2

2. INSTALLATION 4 .......................................................................................

2-1. Installing the AW-3S ........................................................................................................... 4

2-2. Installation location ........................................................................................................... 4

2-3. Installing the bobbin thread remaining amount detection sensor (optional) ............... 4

3. OPERATION PROCEDURE 5 ...................................................................

3-1. 5Opening/closing the cover door .......................................................................................

3-2. How to thread the device with the bobbin thread ........................................................... 6

3-3. How to set a bobbin ........................................................................................................... 8

3-4. Length of remaining thread to be removed ................................................................... 11

3-5. Device operation lamp ..................................................................................................... 12

3-6. To use the AW-3 ................................................................................................................ 13

3-7. Behavior of the AW-3 device when the power is turned ON ........................................ 14

3-8. ................................................................................................... 15Memory switch data list

3-9. Basic operation and setting ............................................................................................ 16

3-10. Operating the AW ........................................................................................................... 17

3-11. Setting the AW number-of-stitches input mode, AW operation mode and

remaining-thread allowance length ................................................................................ 20

3-12. Example of operation..................................................................................................... 27

3-13. Turning OFF of the power ............................................................................................. 32

3-14. Error display and error handling procedure................................................................ 32

3-15. Detection of errors related to the AW ........................................................................... 34

3-15. List of errors ................................................................................................................... 36

4. MAINTENANCE 38 ....................................................................................

4-1. Attaching / removing the cover ...................................................................................... 38

4-2. Cleaning ............................................................................................................................ 39

4-3. Replacing the fuse ........................................................................................................... 41

4-4. Replacing the gripper tube.............................................................................................. 41

4-5. Corrective measure against idling of the bobbin.......................................................... 42

4-6. Adjusting the air ow for the remaining thread guide ................................................. 42

4-7. Attaching/removing the AW main body ......................................................................... 43

5. TROUBLESHOOTING 44 ..........................................................................

– 1 –

1. GENERAL

1 Applicable bobbin, bobbin

case

Exclusive double-capacity bobbin and bobbin case.

2 Applicable thread count #5 to #30 (Japan), 135 to 45 (TEX), 020 to 060 (TKT)

3 Applicable type of thread Synthetic thread

4 Remaining-thread removal and

bobbin winding operation

Possible while the sewing machine is in operation.

5 Condition setting according

to the thread type

Conditions to be met to unravel the thread at the beginning of

winding a bobbin can be set.

6 100,120/200,220,240 Vac ±10 %, Single phase 50/60 HzLine voltage

7 Power consumption 100 VA

8 Air pressure used 0.5 to 0.55 MPa

9 Air consumption 156 Nℓ / min (max. value)

10 Dimensions

700 mm (W

)

× 650 mm (L

)

× 430 mm

) (Accessories includ-

ed)

11 Mass of the device 38 kg

Operating temperature range

5 ˚C to 35 ˚C

Operating humidity range

35 % to 85 % (No dew condensation)

14 - Equivalent continuous emission sound pressure level (LNoise pA) at

the workstation : A-weighted value

≦ 75 dB ; (Includes KpA =

2.5 dB) ; according to ISO 10821- C.6.2 -ISO 11204 GR2 at

remaining-thread removal length = 2 m; Bobbin-thread winding

length (22 m).

Conventionally, a series of operations including the replacement of a bobbin in the sewing machine

hook, removal of thread remaining on a bobbin, winding of a bobbin, threading of the bobbin case ten-

sion spring and trimming of thread have been carried out manually. Now, this device has been devel-

oped to carry out the series of operations full-automatically. This device not only helps increase e󰀩cien-

cy of sewing work but also ensures stable product making in such processes that require high seam

quality.

Refer to the Instruction Manual for the AMS-221EN/AMS224EN/IP-420 for information about the main

body of the sewing machine.

1-1. Specications of AW-3

Product specificaties

Merk:	Juki
Categorie:	Naaimachine
Model:	AW-3S

Heb je hulp nodig?

Als je hulp nodig hebt met Juki AW-3S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Naaimachine Juki

Juki LU2-4410-B1T-CS Handleiding

19 Maart 2024

Juki AW-3SD Handleiding

5 Januari 2024

Juki DNU-1541-7 Handleiding

5 Januari 2024

Juki TU-273 Handleiding

5 Januari 2024

Juki PLK-J12060R Handleiding

1 December 2023

Juki DDL8700A-7 Handleiding

22 Maart 2023

Juki PLK-J12060RH Handleiding

9 Juli 2023

Juki LU2-4652-B1T Handleiding

8 Juli 2023

Juki LU-2860N Handleiding

8 Juli 2023

Juki PLK-G2008H Handleiding

8 Juli 2023

Handleiding Naaimachine

Nieuwste handleidingen voor Naaimachine

Husqvarna-Viking Hiclass E20 Handleiding

25 April 2024

Husqvarna-Viking Eden Rose 250C Handleiding

25 April 2024

Singer SO235 Handleiding

25 April 2024

Husqvarna-Viking Hiclass E10 Handleiding

25 April 2024

Husqvarna-Viking Eden Rose 250M Handleiding

25 April 2024

Husqvarna-Viking Huskylock 90 Handleiding

25 April 2024

Pfaff Hobbylock 4763 Handleiding

25 April 2024

Husqvarna-Viking Metal Hoop 180-130mm Handleiding

25 April 2024

Husqvarna-Viking Huskylock s15 Handleiding

25 April 2024

Husqvarna-Viking Amber Air S600 Handleiding

25 April 2024