JL Audio C1-075ct Handleiding

JL Audio Speaker C1-075ct

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio C1-075ct (8 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 79 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Thank you for choosing JL Audio loudspeakers for
your automotive sound system.
We strongly recommend that you have your new loudspeakers installed by
an authorized JL Audio dealer. Your authorized dealer has the training,
expertise and installation equipment to ensure
optimum performance of these loudspeakers in your vehicle.
If you decide to install the loudspeakers yourself, please read this manual
thoroughly to familiarize yourself with their installation
requirements and setup procedures.
Should you have any questions regarding the instructions in this manual,
please contact your authorized JL Audio dealer for assistance, or call the
JL Audio Technical Support Department at (954) 443-1100
during business hours (USA - Eastern Time Zone).
0.75-inch (19 mm) Component Tweeters
OWNER’S MANUAL
2 | JL Audio - C1-075ct Owner’s Manual
Due to ongoing product development, all specifications are subject to change without notice.
Tweeter Fixture Physical Dimensions Flush-Mount Surface-Mount
Fixture Outer Diameter (A) 1.67 in / 42 mm 1.71 in / 43 mm
Fixture Mounting Hole Diameter (B) 1.46 in / 37 mm N/A
Fixture Mounting Depth (C) 0.40 in / 10 mm N/A
Tweeter Frontal Protrusion (D) 0.23 in / 6 mm 0.76 in / 19 mm
B
A
D
C
D
A
B
A
C
Crossover Network Physical Dimensions
Width (A) 1.96 in / 50 mm
Height (B) 0.90 in / 23 mm
Depth (C) 1.34 in / 34 mm
3
C1-075ct SPECIFICATIONS
Continuous Power Handling: 50 Watts
Recommended Amp Power: 20-50 Watts / ch. (RMS)
Efficiency: 91 dB @ 1W / 1m | 97 dB @ 1W / 0.5m
Sensitivity: 92 dB @ 2.83V / 1m
Nominal Impedance: 6 ohm
Frequency Response: 4 kHz - 24 KHz ± 3 dB
Tweeter:
Edge-driven, silk-suspended aluminum dome
0.75 in. (19 mm) diameter diaphragm / voice coil
Ferrofluid cooling / damping
Neodymium Magnet
Crossover:
2nd order, high-pass filter with inductor and
electrolytic capacitor
Included Components and Parts:
• Two (2) C1-075ct 0.75-inch (19 mm) tweeters
• Two (2) surface-mount tweeter fixtures
• Two (2) C1-075cthp in-line, high-pass filters on
4 ft. (1.2 m) wire harnesses
• Two (2) metal spring clips (for tweeter flush-mounting)
• Four (4) #6 x .625-inch (22 mm) sheet metal screws
• Two (2) 10mm stud bolts with fixed M4 nut
• Two (2) 25mm stud bolts with fixed M4 nut
• Two (2) M5 nuts
GETTING STARTED
• Turn off the audio system. It is also
advisable to disconnect the negative
(–) terminal of your vehicle’s battery
whenever performing installation work.
• Before cutting, drilling or inserting any screw,
check clearances on both sides of the planned
mounting surface. Also check for any potential
obstacles, such as window tracks and motors,
wiring harnesses, etc. Check both sides of the
vehicle, many vehicles are not symmetrical!
• Always wear protective eyewear.


Product specificaties

Merk: JL Audio
Categorie: Speaker
Model: C1-075ct

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio C1-075ct stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker JL Audio

Handleiding Speaker

Nieuwste handleidingen voor Speaker