Jensen PCD163 Handleiding
Jensen
Niet gecategoriseerd
PCD163
Bekijk gratis de handleiding van Jensen PCD163 (46 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 96 mensen en kreeg gemiddeld 4.4 sterren uit 48.5 reviews. Heb je een vraag over Jensen PCD163 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/46
PCD163
Owner's Manual/Manual del Usario/Manual de L'Utilisateur
AM/FM/CD Receiver
Receptor AM/FM/CD
AM/FM/CD Ampli-Syntoniseur
RPT
TRACK
SCN
LOUD
AUX IN
DISP
MODE
BAND
T
U
N
I
N
G
MUTE
PCD163
SEL/MENU
PCD163
2
PREPARATION
Getting Started
It’s a good idea to read all of the instructions
before beginning the installation.
Contents
Installation Instructions.............................. 3
Wiring ........................................................ 5
Operating Instructions ............................... 6
CD Player Operating Instructions............ 10
Care and Maintenance............................ 12
Specifications .......................................... 13
Installation Requirements
This unit is designed for installation in cars,
trucks, and vans with an existing radio opening.
In many cases, a special installation kit will be
required to mount the radio to the dashboard.
These kits are available at electronics supply
stores and car stereo specialty shops. Always
check the kit application before purchasing to
make sure the kit works with your vehicle. If you
need a kit but cannot locate one, call our
customer support line at 1-800-323-4815.
(U.S.A. and Canada only.)
Tools and Supplies
The following tools and supplies are needed to
install the radio.
• Torx type, flathead and Philips
screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio
(screwdriver, socket wrench set or other
tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16-18 gauge speaker wire
Speaker Requirements
Only connect speakers rated with a load
impedance of 4 ohms. Speakers with a load
impedance of less than 4 ohms could damage
the unit.
Disconnect Battery
Before you begin, disconnect the battery
negative terminal.
Toll-Free Installation Assistance
If you require assistance, contact Technical
Support at 1-800-323-4815 from 8:30 a.m. to
7:00 p.m. EST Monday through Friday and from
9:00 a.m. to 5:00 p.m. EST on Saturday.
(U.S.A. and Canada only.)
Pour des instructions en Francais, référez-vous à la page 30.
Para obtener instrucciones en Español, diríjase a la página 16.
PCD163
3
INSTALLATION INSTRUCTIONS
Installation Using the Mounting
Sleeve
1. Slide the mounting sleeve off the chassis.
If it is locked into position, use the removal
tools (supplied) to disengage it.
2. Check the dashboard opening size by
sliding the mounting sleeve into it. If the
opening is too small, carefully cut or file as
necessary until the sleeve easily slides
into the opening. Do not force the sleeve
into the opening or cause it to bend or
bow. Check for sufficient space behind the
dashboard for the radio chassis.
3. Locate the series of bend tabs along the
top, bottom, and sides of the mounting
sleeve. With the sleeve fully inserted into
the dashboard opening, bend as many of
the tabs outward as necessary to firmly
secure the sleeve to the dashboard.
4. Place the radio in front of the dashboard
opening so the wiring can be brought
through the mounting sleeve. Follow the
wiring diagram carefully and make certain
all connections are secure and insulated
with wire nuts or electrical tape. After
completing the wiring connections, turn
the unit on to confirm operation (vehicle
ignition must be “on”). If the unit does not
operate, re-check all wiring until the
problem is corrected.
5. Make sure the radio is right-side up, then
carefully slide the radio into the mounting
sleeve until it is fully seated and the spring
clips lock it into place.
6. Attach one end of the perforated support
strap (supplied) to the screw stud on the
rear of the chassis using the hex nut
provided. Fasten the other end of the
perforated strap to a secure part of the
dashboard either above or below the radio
using the screw provided. Bend the strap
to position it as necessary.
7. Test the radio using the Operating
Instructions that follow.
RPT
TRACK
SCN
LOUD
AUX IN
D PIS
MODE
BAND
T
U
N
I
N
G
MUTE
PCD163
SEL/M ENU
CAUTION: The support strap
must be used to prevent
damage to the dashboard from
the weight of the radio or
improper operation due to
vibration.
CAUTION: For proper operation
of the CD player, the chassis
must be mounted within 20° of
horizontal. Make sure the unit is
mounted within this limitation.
INSTALLATION
BEND TABS
Product specificaties
| Merk: | Jensen |
| Categorie: | Niet gecategoriseerd |
| Model: | PCD163 |
Heb je hulp nodig?
Als je hulp nodig hebt met Jensen PCD163 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Jensen
24 Oktober 2024
8 December 2023
11 Juni 2023
16 Mei 2023
10 Mei 2023
7 Mei 2023
24 April 2023
14 April 2023
2 April 2023
25 Maart 2023
Handleiding Niet gecategoriseerd
- Rome
- TVLogic
- Reflexion
- Blackburn
- Bebob
- Digi-Pas
- Real Cable
- Kenwood
- Kopul
- Telmax
- SKS
- Luxman
- Dinstar
- Aguilar
- Artrom
Nieuwste handleidingen voor Niet gecategoriseerd
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025