JBL Control X Wireless Handleiding

JBL Speaker Control X Wireless

Lees hieronder de 📖 handleiding in het Nederlandse voor JBL Control X Wireless (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

CONTROL X WIRELESS

2-way 5.25” (133mm) Portable Stereo Bluetooth® Speakers

OWNER’S MANUAL

The JBL® brand has been involved in every aspect of music,

film recording and reproduction from live performances to the

recordings you play in the home, car, or on-the-go. We’re confident

that the JBL system you have chosen will provide every note

of enjoyment that you expected and that when you think about

purchasing additional audio equipment for your home, car or office,

you will once again choose a JBL product.

The JBL Control X is an advanced indoor/outdoor* Bluetooth

active loudspeaker system that allows you to enjoy your favorite

music in remote locations around the home or in commercial

spaces. To ensure trouble-free performance, please carefully

read these instructions completely before connecting or using the

system.

*Please note that while the JBL Control X WIRELESS is

an all weather outdoor loudspeaker, it is not waterproof.

These speakers should NOT be submerged or directly

exposed to water, ice, snow or sustained moisture. Do

not spray water into the speaker’s rear port.

THANK YOU FOR CHOOSING THIS JBL® PRODUCT

ENGLISH

UNPACKING THE SYSTEM

Carefully unpack the system. If you suspect damage from transit,

report it immediately to your dealer and/or delivery service. Keep

the shipping carton and packing materials for future use. Open the

package and verify the following contents:

INCLUDED

1 x JBL Control X Wireless Primary speaker

1 x JBL Control X Wireless Secondary speaker

2 x AC power cord

1 x Owner’s Manual

1 x Safety sheet

TOP-PANEL CONTROLS

PRIMARY SPEAKER

1 2 3 4 5 6 7

1. Power

2. Bluetooth pairing (Press and Hold 2 seconds to un-pair current

Bluetooth device)

3. Transport control button (Previous track)

4. Play / Pause

5. Transport control button (Next track)

6. Volume Down

7. Volume Up

8. Battery level indication

9. Front panel LED indication

LED

information

Fixed Quick Flash Regular Flash

White On / No Bluetooth

device connected

Additional speaker association

mode Volume Up and Down

(Stops when reaches Max

or Min)

System is waking up

Blue Bluetooth device

connected

Bluetooth pairing

mode

Note: The front LED indication times out in normal operation mode

Note: to mute the systems simply press and hold volume up and

down simultaneously. Simply press volume up or volume down to un-

mute the system.

SECONDARY SPEAKER

CONTROL X

1. Power

2. Battery level indication

3. Front panel LED indication

LED

information

Fixed Quick Flash Regular Flash

White On / No Bluetooth

device connected

Additional speaker association

mode Volume Up and Down

(Stops when reaches Max

or Min)

System is waking up

Blue Bluetooth device

connected

Bluetooth pairing

mode

REAR-PANEL CONTROLS

PRIMARY SPEAKER

AC IN

AUX-IN

L/R/L+R

P S

MODE WALL/OTHER

23 4

1. AC input connector

2. Auxiliary 3.5mm audio input

3. Primary-Secondary mode selector

4. Boundary compensation switch

a. Wall: Speaker equalization optimized for wall mounting.

b. Other: Speaker equalization optimized for other placement

conditions

5. Left / Right / Left + Right switch

a. Left: Speaker reproduces left channel information only

www.jbl.com

ENGLISH

b. Right: Speaker reproduces right channel information only

c. Left + Right: Mono configuration speaker reproduces left and

right channels information

6. Association pin hole

SECONDARY SPEAKER

AC IN

L/R/L+R

WALL/OTHER

1. AC input connector

2. Boundary compensation switch

a. Wall: Speaker equalization optimized for wall mounting.

b. Other: Speaker equalization optimized for other placement

conditions

3. Left / Right / Left + Right switch

a. Left: Speaker reproduces left channel information only

b. Right: Speaker reproduces right channel information only

c. Left + Right: Mono configuration speaker reproduces left and

right channels information

4. Association pin hole

PLACING THE SPEAKERS

These speakers can be mounted or placed on a stand, shelf or table.

The following figure shows a possible indoor application. For optimal

performance, do not block the rear port on the back of each speaker.

Left

Surround

Channel

Right

Surround

Channel

Left Front

Channel

Subwoofer

Right Front

Channel

Left

Rear

Channel

Right

Rear

Channel

Center

Channel

Couch

QUICK SETUP AND OPERATION

The speaker set is already factory setup to operate as a pair (primary

and secondary).

1. Connect AC power cords to AC-IN plug located at the rear of each

speaker. Keep AC plugged to maintain battery fully charged.

2. Press power button on each speaker(s) to start operation.

3. Press Bluetooth button and pair with streaming device. (Refer to

Listening to Audio from a Bluetooth capable device section below)

4. If desired to use in battery mode, just unplug the AC power. Speaker

and audio will not be interrupted. Reconnect to AC to recharge

battery.

Note: Primary and Secondary speakers’ factory default settings are as

Control / Switch Primary Secondary

Mode (P) N/A

Wall/ Other Other Other

L/R/L+R (L) (R)

Note: When the system is not playing music it will go automatically

into auto standby mode. To reactivate the system, simply start

playing music and the system will resume automatically. A slight

delay may occur before the secondary speaker wakes up as it needs

resynchronization with the primary speaker. During this phase the front

LED of the secondary speaker will be blinking.

Note: If the system is manually powered off using the power button, it

will need to be manually powered on first to resume playing music.

The system also features sound prompt commands for the following

action / operation

1. Power On

2. Power Off

3. Bluetooth pairing mode

4. Bluetooth connection success

5. Association mode (see Speaker association section)

6. Battery low level

LISTENING TO AUDIO FROM A BLUETOOTH-

CAPABLE DEVICE

1. With speaker(s) powered on AC or Battery power, Press Bluetooth

button on primary speaker

2. An audible prompt will indicate that the speaker successfully

entered BT pairing mode. The front LED will also blink Blue as an

indication that BT pairing mode is enabled.

3. Search and pair with “JBL Control X” from your Bluetooth streaming

device.

4. An audible confirmation will be played once the streaming device

successfully paired with the speaker. The front LED will stop blinking

and remain Blue. Secondary speaker will confirm Bluetooth pairing

by flashing front panel LED Blue for a few seconds.

Note: Only one Bluetooth device can be paired at the same time with

the system. If you need to un-pair the current Bluetooth device to

connect a new one simply press and hold the Bluetooth button on the

primary speaker for more than 2 seconds to disconnect current device.

Then resume the pairing process above from step 2.

FPO

Product specificaties

Merk:	JBL
Categorie:	Speaker
Model:	Control X Wireless
Kleur van het product:	Black, Red
Gewicht:	2950 g
Breedte:	165 mm
Diepte:	159 mm
Hoogte:	235 mm
Gebruikershandleiding:	Ja
Bluetooth:	Ja
Connectiviteitstechnologie:	Bedraad en draadloos
Type stroombron:	AC, Battery
Meegeleverde kabels:	AC
Snelstartgids:	Ja
Gemiddeld vermogen:	30 W
Ingangsspanning:	100 - 240 V
Soort voeding:	AC
Aanbevolen gebruik:	Universeel
3,5mm-connector:	Ja
Ingebouwde accu:	Ja
Audio-uitgangskanalen:	2.0 kanalen
Speaker plaatsing:	Tafelblad/Boekenplank
Aantal drivers:	2
Woofer:	Ja
Frequentiebereik:	62 - 20000 Hz
Signaal/ruis-verhouding:	75 dB
Bereik van Bluetooth:	10 m
Luidspreker soort:	2-weg
Versterker:	Ingebouwd
Diameter woofer:	5.25 "
Diameter hogetonenluidspreker:	1 "
Tweeter:	Ja
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Ingangsfrequentie voeding:	50 - 60 Hz
Versterker klasse:	D
Driver cone material:	Polypropyleen
Transmissiefrequentie:	2.4 GHz