JANDY VSFHP185DV2ASP Handleiding
Pagina's 84 Pomp
Bekijk de handleiding van JANDY VSFHP185DV2ASP gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
Installation and Operation Manual
Manuel d’installation et d’utilisation
Manual de instalación y operación
Variable-Speed Pumps
Models:VSFHP185DV2ASPVSFHP270DV2ASPVSPHP270DV2ASP
VSSHP270DV2ASPVSFHP3802ASPVSSHP3802ASP
Essential installation and startup instructions are included in this manual. Additional operation
and troubleshooting information is available online by scanning the QR code with your phone
or visiting jandy.com
WARNING
FOR YOUR SAFETY –This product must be installed and serviced by a contractor who is licensed and qualified in
poolequipment by the jurisdiction in which the product will be installed where such state or local requirements exist.
Themaintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all
of the instructions in this manual can be followed exactly. Before installing this product, read and follow all warning notices
and instructions that accompany this product. Failure to follow warning notices and instructions may result in property
damage, personal injury, or death. Improper installation and/or operation may void the warranty.
Improper installation and/or operation can create unwanted electrical hazards which may cause serious injury, property
damage, or death.
ATTENTION INSTALLER –This manual contains important information about the installation, operation and
safe use of this product. Thisinformation should be given to the owner/operator of this equipment.
Page 2
ENGLISHJandy
®
Variable-Speed Pumps | Installation and Operation Manual
Table of Contents
Important Safety Instructions .......................2
1.1 Pool Pump Suction Entrapment
PreventionGuidelines ..............................3
Section 1. General Description ...................4
1.1 Introduction ..............................................4
1.2 Product Dimensions ................................5
1.3 Product Specifications .............................5
1.4 Product Contents .....................................6
Section 2. Installation Information ..............7
2.1 Zero Clearance TEFC Motor ....................7
2.2 Plumbing ..................................................7
2.3 Electrical Installation ..............................10
2.4 Pump Controller / Automation
System Setup ........................................12
2.5 DIP Switch Settings ...............................12
2.6 Auxiliary Relay Operation .......................13
Section 3. Dry Contact Operation .............13
3.1 Dry Contact Speed Settings ..................13
3.2 Conduct Pressure Test ...........................15
Section 4. Operation ..................................16
4.1 Startup ...................................................16
Section 5. Service & Maintenance ............17
5.1 Clean Pump Basket ...............................17
5.2 Removing the Pump Lid ........................17
5.3 Winterizing the Pump .............................18
Section 6. Troubleshooting and Repair ....19
6.1 Service Technician Maintenance ...........20
Section 7. Product Specifications and
TechnicalData ..........................21
7.1 Exploded Views .....................................21
7.2 Performance Curves ..............................22
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
RISK OF SUCTION ENTRAPMENT HAZARD, WHICH, IF NOT AVOIDED, CAN RESULT IN SERIOUS INJURY OR DEATH.Do not
block pump suction, as this can cause severe injury or death. Do not use this pump for wading pools, shallow pools, or
spas containing bottom drains, unless the pump is connected to at least two (2) functioning suction outlets, and/or in
accordance with the latest version of ANSI
®
/PHTA
®
/ICC-7 the standard for Suction Entrapment Avoidance in Swimming
Pools, Wading Pools, Spas, Hot Tubs, and Catch Basins. Suction outlet (drain) assemblies and their covers must be
certified to the latest published edition of ANSI
®
/ASME
®
A112.19.8, or its successor standard, ANSI/APSP-16.
To reduce the risk of injury, do not permit children to use this product.
To reduce the risk of property damage or injury, do not attempt to change the backwash (multiport, slide, or full flow) valve
position with the pump running.
Jandy pumps are powered by a high voltage electric motor and must be installed by a licensed or certified electrician or a
qualified swimming pool service technician.
Due to the potential risk of fire, electric shock, or injuries to persons, Jandy pumps must be installed in accordance with
the National Electrical Code
®
(NEC
®
), all local electrical and safety codes, and the Occupational Safety and Health Act
(OSHA). Copies of the NEC may be ordered from the National Fire Protection Association, 1 Batterymarch Park, Quincy,
MA 02169, or from your local government inspection agency.
RISK OF ELECTRIC SHOCK, FIRE, PERSONAL INJURY, OR DEATH.(For all permanently installed units intended for use on 15
or 20 ampere, 120 through 240 volt, single phase branch circuits). Connect only to a branch circuit that is protected by a
ground-fault circuit-interrupter protection for personnel (GFCI). Contact a qualified electrician if you cannot verify that the
circuit is protected by a GFCI. AGFCI should be provided by the installer and should be tested on a routine basis. To test
the GFCI, push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the
GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button
being pushed, a ground current is flowing, indicating the possibility of electrical shock. Do not use the device. Disconnect
the device and have the problem corrected by a qualified service representative before using.
Jandy
®
Variable-Speed Pumps | Installation and Operation ManualENGLISH
Page 3
WARNING
Incorrectly installed equipment may fail, causing severe injury or property damage.
• Do not connect the system to an unregulated city water system or other external source of pressurized water
producing pressures greater than 35 PSI.
• Trapped air in system can cause the filter lid to be blown off, which can result in death, serious personal injury, or
property damage. Be sure all air is out of the system before operating.
To minimize the risk of severe injury or death, the filter and/or pump should not be subjected to the piping system
pressurization test.
Local codes may require the pool piping system to be subjected to a pressure test. These requirements are generally not
intended to apply to the pool equipment such as filters or pumps.
Jandy pool equipment is pressure tested at the factory.
However, if the WARNING cannot be followed and pressure testing of the piping system must include the filter and/or
pump, BE SURE TO COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS:
• Check all clamps, bolts, lids, lock rings and system accessories to ensure they are properly installed and secured before testing.
• RELEASE ALL AIR in the system before testing.
• Water pressure for test must NOT EXCEED 35 PSI.
• Water temperature for test must NOT EXCEED 100°F (38°C).
• Limit test to 24 hours. After test, visually check system to be sure it is ready for operation.
NOTICE:
These parameters apply to Jandy equipment only. For non-Jandy equipment, consult equipment
manufacturer.
Chemical spills and fumes can weaken pool/spa equipment. Corrosion can cause filters and other equipment to fail,
resulting in severe injury or property damage. Do not store pool chemicals near your equipment.
CAUTION
Do not start pump dry!Running the pump dry for any length of time will cause severe damage and may void the warranty.
This pump is for use with permanently installed pools and may also be used with hot tubs and spas, if so marked. Do not
use with storable pools. A permanently installed pool is constructed in or on the ground or in a building such that it cannot
be readily disassembled for storage. A storable pool is constructed so that it may be readily disassembled for storage and
reassembled to its original integrity.
Do not install within an outer enclosure or beneath the skirt of a hot tub. The pump requires adequate ventilation to
maintain air temperature at less than the maximum ambient temperature rating listed on the motor rating plate.
In order to avoid premature failure or damage to the pump motor, protect the pump from direct water exposure from
sprinklers, water runoff from rooftops and drainage, etc. Failure to comply may cause pump failure, and may void the
warranty.
1.1 Pool Pump Suction Entrapment PreventionGuidelines
WARNING
SUCTION HAZARD. Can cause serious injury or death. Do not use this pump for wading
pools, shallow pools or spas containing bottom drains, unless the pump is connected
to at least two (2) functioning suction outlets and/or in accordance with the latest
version of ANSI
®
/PHTA
®
/ICC-7 the standard for Suction Entrapment Avoidance in
Swimming Pools, Wading Pools, Spas, Hot Tubs, and Catch Basins.
Product specificaties
| Merk: | JANDY |
| Categorie: | Pomp |
| Model: | VSFHP185DV2ASP |
Heb je hulp nodig?
Als je hulp nodig hebt met JANDY VSFHP185DV2ASP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden