Intermatic IOS-DOV-DT Handleiding

Bekijk gratis de handleiding van Intermatic IOS-DOV-DT (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.3 sterren uit 5 reviews. Heb je een vraag over Intermatic IOS-DOV-DT of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Dual Technology

PIR/Ultrasonic

In-Wall Occupancy / Vacancy

Sensor Switch

MODEL: IOS-DOV-DT

Ratings:

Input Voltage: 120/277 VAC, 50/60 Hz

Electronic Ballast (LED): 600 VA, 120 VAC; 1385 VA, 277 VAC

Tungsten (Incandescent): 800 W, 120 VAC

Fluorescent / Ballast : 800 VA, 120 VAC

Resistive (Heater): 800 W, 120 VAC

Motor: 1/4 HP, 120 VAC

Time Delay: 15 Sec - 30 Min

Light Level: 10 fc - Daylight

Walk Through Mode: 3 min if no activity after 30 sec

PIR Sensitivity Adjustment: 50% or 100% (DIP switch)

Ultrasonic Sensitivity Adjustment: 30% to 100%

Coverage -PIR: up to 1200 ft

2

(110m

2

)

US: up to 400 ft

2

(37m

2

)

Operation Temperature: 32° - 131° F / 0° - 55° C

No minimum load required

Figure 4

INSTALLATION AND CONFIGURATION INSTRUCTIONS

Figure 1

Figure 2

DESCRIPTION:

The IOS-DOV-DT series Dual Technology Occupancy Sensors In-Wall sensor switch controls

a load based on occupancy, vacancy and ambient light levels. It combines passive infrared

(PIR) and ultrasonic technologies to help avoid false triggering while increasing presence

detection. Selectable modes allow the sensor to turn load ON and hold it ON as long as either

or both technologies detect occupancy. If no movement is detected for a user-specified time

of 15 seconds to 30 minutes, the load is turned OFF. The sensor provides a 180° coverage

pattern, up to 1200 ft

2

(110

m2

) for PIR and 400 ft

2

(37

m2

) for Ultrasonic sensor.

INSTALLATION

1. Make sure power is turned off at main disconnect.

2. Remove existing single pole switch or dimmer installation, if applicable.

3. Remove 3/4” (1.9 cm) of insulation from each circuit conductor. Make sure the ends of

wires are straight.

4. Connect lead wires as shown in WIRING DIAGRAM (see Figure 2): Black lead to Line

(Hot), Red lead to Load wire, White lead to Neutral wire, Green lead to Ground.

5. Gently position wires in wall box, attach sensor switch to the box.

6. Mount device “TOP” up.

7. Restore power at circuit breaker or fuse, wait one minute.

8. Remove the small cover plate by lifting from bottom edge (see Figure 3).

9. Locate the adjustment knobs on the control panel to perform tests and adjustments

(see Figure 4).

10. Replace the small cover plate after testing and adjusting.

11. Attach the wall plate.

Figure 3

WARNING

Risk of Fire or Electric Shock

• Disconnect power at the circuit breaker(s) or fuses before installing or servicing.

• Installation and/or wiring must be in accordance with national and local electrical code

requirements.

• Use COPPER conductors ONLY.

• Indoor dry location use only.

• Do not exceed electrical ratings.

LOCATION/MOUNTING

Since this device responds to temperature changes, care should be taken when mounting

the device. DO NOT mount directly above a heat source, in a location where hot or cold drafts

will blow directly on the sensor, or where unintended motion will be within the sensor’s

field-of-view.

SENSOR ADJUSTMENT

Remove the cover from the sensor.

NOTE: There is a 40 sec warm-up period when power is first applied to unit.

The sensors are factory preset to allow for quick installation in most applications. Follow

this procedure to verify the sensor coverage and customize the settings.

BAND SWITCH

Sensor has the ability to be set as an occupancy or vacancy sensor. The main difference is that when set to

vacancy mode the load will only turn ON with the push button.

Mode

PositionDescriptionReact to the push button

OFF

LeftCircuit is permanently openNone

OCC

CenterOccupancy Mode: Automatic ON, Automatic OFF

after set time delay.

Manually toggles the load

ON/OFF.

VAC

RightVacancy Mode: Manual ON only, Automatic OFF

after set time delay

Manually toggles the load

ON/OFF.

PIR Coverage: 1200 ft

2

(110

m2

)

Ultrasonic Coverage: 400 ft

2

(37

m2

)

Product specificaties