Indesit DIE 2B19 UK Handleiding

Indesit Vaatwasser DIE 2B19 UK

Lees hieronder de 📖 handleiding in het Nederlandse voor Indesit DIE 2B19 UK (8 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

Before using the appliance carefully read Safety Instructions guide.

APPLIANCE

THANK YOU FOR BUYING A INDESIT PRODUCT.

In order to receive a more complete assistance, please

You can download the Safety Instructions and the

User Manual, by visiting our website docs.indesit.eu

and following the Instructions on the back of this

booklet.

1. Upper rack

2. Foldable aps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Cutlery basket

7. Lower spray arm

8. Filter Assembly

9. Salt reservoir

10. Detergent and Rinse Aid dispensers

11. Rating plate

12. Control panel

1 2 4 53

1. ON-OFF / Reset button with indicator light

2. Program selection button / Push&Go

3. Salt rell indicator light

4. Program indicator lights

5. START/Pause button with indicator light

DAILY REFERENCE

GUIDE

CONTROL PANEL

0000 000 00000

Service:

PRODUCT DESCRIPTION

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the reta-

ining elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher

(see PRODUCT DESCRIPTION) and must be lled when the SALT REFILL

indicator light in the control panel is lit..

1. Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2. Only the rst time you do this: ll the salt

reservoir with water.

3. Position the funnel (see gure) and ll the salt

reservoir right up to its edge (approximately

1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

Whenever you need to add salt, it is mandatory to complete the

procedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory sets the default value for the water hardness

• Switch on the appliance by pressing the button.ON/OFF

• Switch o the appliance by pressing the button.ON/OFF

• Hold down button for 5 seconds, until you hear a beep.P

• Switch on the appliance by pressing the button.ON/OFF

• The program indicator light of the current set level ashes.

• Press button P to select the desired hardness level (see WATER

HARDNESS TABLE).

• Switch o the appliance by pressing the button.ON/OFF

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indi-

cator light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Using of Salt is recommended with any type of dishwasher deter-

gent.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser should A

be lled when when the dark optical indicator on the dispenser door C

becomes transparent.

1. Open the dispenser B by pressing and pulling up the tab on the lid .

2. Pour in the rinse aid (max.110 ml), making sure it does not overow

from the dispenser. If this happens, clean the spill immediately with

a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID

f you are not completely satised with the drying results, you can adjus

the quantity of rinse aid used.

• Switch the dishwasher on using the button.ON/OFF

• Switch it o using the button.ON/OFF

• Press button three times - a beep will be heard.P

• Switch it on using the button.ON/OFF

• The program indicator light of the current set level ashes.

• Press button P to select the level of rinse aid quantity to be supplied.

• Switch it o using the buttonON/OFF

Setting is complete!

If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied.

A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is specic to the model, please follow instruction

above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (2-3).

• If there are drops of water or limescale marks on the dishes, set a

mid-range number (4-5 ).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser use the opening device D.

Introduce the detergent into the dry dispenser E only. Place the

amount of detergent for pre-washing directly inside the tub.

1. When measuring out the detergent

refer to the mentioned earlier infor-

mation to add the proper quantity.

Inside the dispenser there are E

indications to help the detergent

dosing.

2. Remove detergent residues from

the edges of the dispenser and clo-

se the cover until it clicks.

3. Close the lid of the detergent di-

spenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program.

Usage of detergent not designed for dishwashers may cause mal-

function or damage to the appliance.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

°Clark

English degrees

1 Soft 0 - 6 0 - 10 0 - 7

2 Medium 7 - 11 11 - 20 8 - 14

3 Average 12 - 16 21 - 29 15 - 20

4 Hard 17 - 34 30 - 60 21 - 42

5 Very hard 35 - 50 61 - 90 43 - 62

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.

Note for Test Laboratories:

For information on comparative EN testing conditions, please send an email to the following address: assistenza_en_lvs@indesitcompany.com

Pre-treatment of the dishes is not needed before any of the programs.

*) Values given for programmes other than the eco programme are indicative only. The actual time may vary depending on many factors such as tem-

perature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected

options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Program

Drying

phase

Duration

of wash

program

(h:min)*)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

1Eco 50° 3:20 12,0 1,04

2Intensive 65° 2:30 16,0 1,50

3Mixed 55° 2:25 16,0 1,35

4Fast&Clean 28’

45°

-0:28 9,0 0,60

5Push&GO 50° 1:25 11,5 1,10

PROGRAMS TABLE

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

1 ECO

Eco program is suitable to clean normally soiled tableware, that for this

use, it is the most ecient program in terms of its combined energy

and water consumption, and that it is used to assess compliance with

the EU Ecodesign legislation.

2 INTENSIVE

Program recommended for heavily soiled crockery, especially suitable

for pans and saucepans (not to be used for delicate items).

3 MIXED

Mixed soil. For normally soiled dishes with dried food residues.

4 FAST&CLEAN 28’

Program to be used for half load of lightly-soiled dishes with no dried

food residues. Does not have drying phase.

5 PUSH & GO

Everyday wash and dry cycle that ensures great cleaning performance

in a short time without the need to pre-treat dishes.

Notes:

Please note that cycle Fast&Clean is dedicated for lightly soiled dishes.

PUSH&GO

Push&Go ( ) button is an easily distinguishable button that allows you direct access to the Push&Go program, a wash and dry cycle that P

ensures great cleaning performance in a short time. You don’t have to worry which program to choose, Push&Go cycle will do the work

for you.

To select Push&Go program, switch on appliance, press only button for 3 seconds (corresponding indicator lights up) and close the P

door within 4 seconds.

Product specificaties

Merk:	Indesit
Categorie:	Vaatwasser
Model:	DIE 2B19 UK
Apparaatplaatsing:	Semi-ingebouwd
Soort bediening:	Knoppen
Ingebouwd display:	Ja
Gewicht:	32100 g
Breedte:	598 mm
Diepte:	555 mm
Hoogte:	820 mm
Netbelasting:	1900 W
Aantal couverts:	13 couverts
Deurkleur:	Wit
Snoerlengte:	1.3 m
Duur cyclus:	200 min
Geluidsniveau:	49 dB
Energie-efficiëntieklasse:	F
Gewicht verpakking:	33900 g
Geschikt voor paneelaanpassing:	Ja
Installatie compartiment breedte:	600 mm
Installatie compartiment diepte:	560 mm
Installatie compartiment hoogte:	900 mm
Waterconsumptie per cyclus:	12 l
Stroom:	13 A
Installatie compartiment hoogte (min):	820 mm
Geïntegreerde timer:	Ja
Geluidsemissieklasse:	C
Energieverbruik per 100 cycli:	104 kWu
Verstelbare voeten:	Ja
Productafmeting:	Volledige grootte (60 cm)
Kleur bedieningspaneel:	Wit
Zout indicator:	Ja
Glansmiddel indicator:	Ja
Afwasprogramma's:	Eco, Intensive 65°C
Lengte afvoerslang:	1.5 m
Lengte watertoevoerslang:	1.55 m
Installatie compartiment hoogte (max):	900 mm
Temperatuur (max):	0 °C
Manden verstelbare plaatsing:	Bovenste
AC-ingangsspanning:	230 - 240 V
AC-ingangsfrequentie:	50 Hz
Energie-efficiëntieschaal:	A tot G