Illustra IPS02-B12-OI03 Handleiding

Bekijk gratis de handleiding van Illustra IPS02-B12-OI03 (2 pagina’s), behorend tot de categorie Bewakingscamera. Deze gids werd als nuttig beoordeeld door 28 mensen en kreeg gemiddeld 4.5 sterren uit 9 reviews. Heb je een vraag over Illustra IPS02-B12-OI03 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

2. Attaching the camera to the mounting arm (continued)

B. Place the camera onto the hinge (1) (Figure 5) and release the pin so that

the camera is attached to the mounting arm plate.

Figure 5

C. See step 4 to connect the power cable and then continue on at step D.

D. Flip the camera so that it sits properly on the mounting plate and arm

secure it to the mounting arm plate th the four T10 screws (1) (Figure wi6).

Quick Start Guide

(--8200163004_A0)

Illustra Pro Gen 3 Bullet Cameras

In the box

 4 x plastic screw anchors (use on masonry walls and wood)

Phillips pan head tapered screw TP6x32 (use on masonry wall and wood) 4 x mm

 4 x Phillips pan head tapered screw M5x8mm (Adaptor plate base)

Printed Quick Start Guide 1 x

Printed regulatory document 1 x

NTSC / PAL output female BNC cable 1 x

 1 x RJ45 Connector

 1 x Terminal block

Mounting arm 1 x

Mounting template 1 x

 1 x Desiccant bag

 4 Toggle screw (Expansion Bolt) x

 1 x T10 security Torx wrench

 1 x Universal electrical box mounting plate (IPSMDEBPLATE)

 1 x Pendant / pole mount adaptor

 1 x rubber plug (with two holes) and 1 rubber pin

 1 x rubber plug (with no holes)

 1 x 4mm Allen key

Installation tools

 1 x Drill

 1 x T10 security Torx wrench

 1 x Phillips screw driver

Quick reference

Default IP: 192.168.1.168 (DHCP enabled)

Default Username and Password: admin

Note: You can attach the camera to a surface or directly to a pendant or pole 1 ½ ‘’

Male NPT pipe using the pendant / pole mount adaptor. (The pendant / pole mount

adaptor can be attached to a standard 1 ½‘’ NTP pipe using threads or set screws).

Note: To ensure optimal lens performance, JCI recommends using the automated

lens calibration feature within the web GUI following initial camera installation.

1. Attaching the mounting arm to a surface

A. Place the mounting template provided on the surface and drill four 8mm

(0.3inch) holes. 14

B. sert the four screw anchors into the four holes on the surface. In

C. After passing all required cabling through the mounting arm, place the

mounting arm (1) (Figure 1) on the surface and align the four holes on the

mounting arm (2) (Figure 1) with the four screw anchors or expansion bolts

on the surface (3) (Figure 1).

D. Insert the rubber plug into the top hole on the mounting arm (4) (Figure 1) to

prevent water from entering the mounting arm.

Figure 1

1. Attaching the mounting arm to a surface (continued)

E. Securely attach the mounting arm to the surface with the four TP6x32mm

screws (1) (Figure 2).

Figure 2

F. Insert the Ethernet cable through the waterproof rubber (1) (Figure 3) and if

not using both grommet holes insert the rubber pin (2) (Figure 3) into the

waterproof rubber.

G. Insert the waterproof rubber onto the mounting arm plate. (3) (Figure 3).

1. Attaching the mounting arm to a surface (continued)

Figure 3

2. Attaching the camera to the mounting arm

A. Push the pin (1) (Figure. 4) from the mounting arm hinge.

Figure 4

2. Attaching the camera to the mounting arm (continued)

Figure 6

3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe

A. Place the pendant/pole mount adaptor (1) (Figure 7) around a standard 1

½‘’ Male NPT threaded water pipe (2) (Figure 7) and securely attach the

two M3x0.5P (L = 6mm) screws on the pendant mount adaptor with the T10

security Torx wrench.

Figure 7

Product specificaties