IFM UT0038 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor IFM UT0038 (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/9
1. Setzen Sie die Verschraubung
(C) in den Prozeßanschluß ein
und ziehen Sie sie fest.
Verwenden Sie eine Dichtung,
wenn die Applikation es ver-
langt.
2. Fetten Sie alle Teile des Adap-
ters ein: Überwurfmutter(A),
Progressivring (B), Gewinde
und Konus der Verschraubung
(C).
3. Setzen Sie den Progressivring
ein. ACHTUNG: das verjüngte
Ende muß in den Konus zei-
gen.
4. Schrauben Sie die Überwurf-
mutter auf und setzen Sie den
Sensor (D) ein.
5. Ziehen Sie die Überwurfmutter
mit der Hand fest und bringen
Sie einen Markierungsstrich (E)
an.
6. Schieben Sie den Sensor auf
die gewünschte Tauchtiefe.
Halten Sie ihn fest und ziehen
Sie die Überwurfmutter mit
einem Werkzeug um 2 volle
Umdrehungen an.
Wiederholmontage
Sie können den Sensor demontieren, um z. B. die Sensorspitze zu rei-
nigen. Setzen Sie danach den Sensor wieder ein und ziehen Sie die
Überwurfmutter ohne erhöhten Kraftaufwand fest.
Montageanleitung
Installation Instructions
Notice de Montage
Schneidring-
verschraubung
Progressive ring fitting
Raccord avec bague
progressive
Sachnr. 701308/01 01/99
C
C
B
A
GREASE
D
I
E
1. Insert the fitting (C) into the
process connection and
tighten.
Use an appropriate seal if
required for the application.
2. Grease all parts of the adapter:
coupling nut (A), progressive
ring (B), thread and cone of
the fitting (C).
3. Position the progressive ring.
NOTE: tapered end into the
cone.
1. Visser le raccord (C) dans le
piquage. Utiliser un joint
d' tanch ité é é si nécessaire pour
l'application.
2. Graisser toutes les parties de
l'adaptateur: écrou (A), bague
progressive (B), filetage et
embout conique du raccord
(C).
3. Insérer la bague progressive.
REMARQUE: l'extr coni-émité
que doit s'adapter dans l'emb-
out conique.
4. Visser l' crou et ins rer laé é
sonde (D).
5. Serrer l' crou manuellement eté
le marquer d'un trait (E).
6. Ins rer la sonde jusqu' la pro-é à
fondeur souhait e. La tenir eté
serrer l' crou en faisant 2 toursé
complets à l'aide d'une clé.
Maintenance de la sonde
Vous pouvez d monter la sonde afin de nettoyer par exemple sa par-é
tie sensible. Ins rer la sonde de nouveau et serrer l' crou sans forcer.é é
4. Attach the coupling nut and
insert the sensor (D).
5. Tighten the coupling nut
manually and mark its position
with a line (E).
6. Adjust the sensor to the requi-
red installation depth. Hold it
and tighten the coupling nut
by 2 full turns.
Repeated mounting
You can remove the sensor e.g. to clean the tip. Then insert the sen-
sor again and tighten the coupling nut being careful not to apply too
much force.
C
C
B
A
GREASE
D
I
E
C
C
B
A
GREASE
D
I
E


Product specificaties

Merk: IFM
Categorie: Niet gecategoriseerd
Model: UT0038

Heb je hulp nodig?

Als je hulp nodig hebt met IFM UT0038 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd IFM

IFM

IFM DP4302 Handleiding

12 April 2024
IFM

IFM EVCB02 Handleiding

11 Maart 2024
IFM

IFM EVCB03 Handleiding

11 Maart 2024
IFM

IFM EVF666 Handleiding

11 Maart 2024
IFM

IFM TM4599 Handleiding

8 Januari 2024
IFM

IFM ZB0074 Handleiding

8 Januari 2024
IFM

IFM EVF661 Handleiding

8 Januari 2024
IFM

IFM IIP201 Handleiding

7 Januari 2024
IFM

IFM DP4200 Handleiding

7 Januari 2024
IFM

IFM IIP200 Handleiding

7 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd