Icom OPC-2389 Handleiding

Bekijk gratis de handleiding van Icom OPC-2389 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 37 mensen en kreeg gemiddeld 4.7 sterren uit 6 reviews. Heb je een vraag over Icom OPC-2389 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

CONNECTION CABLE

INSTRUCTIONS

Thank you for choosing this Icom product.

The OPC-2389 connection cable is used to connect a

serial communication device to the VE-PG3 or VE-PG4.

READ ALL INSTRUCTIONS carefully and completely

before using this product.

Turn OFF the all devices that are connected to the VE-PG3 or VE-PG4, and then connect the OPC-2389, as shown below.

1

CONNECTING THE OPC-2389

CAUTION

•Verify that both the serial communication and the VE-PG3 or VE-PG4 are turned OFF when connecting or disconnecting

the cable.

• Hold the connector body when connecting or disconnecting them.

• Never bend or pinch the cable.

• Never place a heavy object on the cable.

• Never touch the cable with wet hands.

•

Always connect the cable correctly. An incorrect connection could damage the VE-PG3 or VE-PG4 and/or the connected device.

• Never add a pulling tension to the cable.

•Never use the OPC-2389 with any device other than VE-PG3 and VE-PG4.

Some serial communication devices may not be used.

VE-PG4 (Rear view)

OPC-2389

•

This is an example of connecting a serial communication device to the [EXT1] port.

A1A4~B1B4~C1C4~

A1A4~B1B4~C1C4~

A1A4~B1B4~C1C4~

A1A4~

BC

Be sure to insert the

connectors top side up.

Bottom

To a serial communication device

Top

B

1234

qtrew

yoiu

BC

When other cables are connected, you can

use needle-nose pliers to carefully insert or

remove connectors.

VE-PG4 (Rear view)VE-PG4 (Rear view)

Needle-nose pliersNeedle-nose pliers

NEVER pull the connector by holding the

cable. This will damage the cable.

*If the cable becomes damaged, replace the

connector(s). See “REPLACING THE

CONNECTOR” to the right for replacement

details.

Connector

body

Connector

body

REPLACING THE CONNECTOR

If the cable becomes damaged, replace the connector(s). Make wire connections as described below.

• Spare connectors*

1

are supplied with the VE-PG3 or VE-PG4.

• If reconnecting is repeated about 30 times, replace the connector.

*

1

Manufacturer: DDK. Name: 232D-04S1B-DA5-FA

DO NOT lock the connector parts before inserting all wires.

Press the clear insert down

until it locks in place.

• After the insert is locked, it is

impossible to release it again.

3

Insert the wires into the holes

according to the assigned pin

numbers.

2

Connector

(Supplied with

the VE-PG3

or VE-PG4)

Connector

(Supplied with

the VE-PG3

or VE-PG4)

The wires for each hole

are assigned by color. See

the illustration below.

OPC-2389

BC

Pin No.

OrangeOrange

BlueBlue

YellowYellow

GrayGray

B

Connector top (Expanded view)

BrnBrnowow

GreenGreen

PurplePurple

RedRed

C

12341234

OPC-2389 connection and wires assignment

Icom and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United

Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries.

A7471X-1J-2

Printed in Japan

© 2018–2023 Icom Inc.

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

Jan. 2023

OPC-2389

Cut the wires*

2

*

3

near the connector.

*

2

Remove the cable

from the VE-PG3

or VE-PG4, before

cutting the wires.

*

3

DO NOT cut the wires too short.

Otherwise it will be difficult to

reconnect them to the VE-PG3 or VE-

PG4.

1

1234

DISPOSAL

The crossed-out wheeled-bin symbol on your

product, literature, or packaging reminds you

that in the European Union, all electrical and

electronic products, batteries, and

accumulators (rechargeable batteries) must

be taken to designated collection locations at

the end of their working life. Do not dispose of these products

as unsorted municipal waste. Dispose of them according to

the laws in your area.

ABOUT CE

Versions of the OPC-2389 which have the “CE”

symbol on the product comply with the essential

requirements of the 2014/30/EU directive for

Electromagnetic Compatibility.

Below statement is for UKCA purpose only

United Kingdom Authorised Importer: Icom (UK) Ltd.

Address: Blacksole House, Altira Park, Herne Bay, Kent,

CT6 6GZ, U.K.

Product specificaties