Honeywell RPLS530A1038 Handleiding

Bekijk gratis de handleiding van Honeywell RPLS530A1038 (20 pagina’s), behorend tot de categorie Csavaros gép. Deze gids werd als nuttig beoordeeld door 18 mensen en kreeg gemiddeld 4.5 sterren uit 7 reviews. Heb je een vraag over Honeywell RPLS530A1038 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

RPLS530A/RPLS531A 1/6

The RPLS530A/RPLS531A switch can be used in a single-pole or 3-way

installation with the following types of lighting:

• Incandescent

• Halogen

• Low-voltage halogen with transformer

• Fluorescent

The

RPLS530A/RPLS531A

switch cannot be used with a load below 40

W, a load above 500 W or a motor.

Cut power at the circuit breaker to avoid electric shock.

Remove the existing switch. (For a 3-way installation, identify and

label the wire that is connected to the “common” screw.)

Install the new switch (refer to the appropriate section below).

Apply power at the circuit breaker.

SINGLE-POLE INSTALLATION

Connect wires "2" and "C" of the RPLS530A/RPLS531A to the line

(120 V) wire.

EXISTING 3-WAY INSTALLATION

Connect wire "C" of the RPLS530A/RPLS531A to the "common" wire,

identified when removing the old switch. Connect the other two

RPLS530A/RPLS531A wires to the two remaining wires.

At the other 3-way switch, connect the jumper wire between the "com-

mon" screw and the screw where wire "1" of the RPLS530A/RPLS531A

is connected.

NEW 3-WAY INSTALLATION

The jumper wire is not required in this installation. A single-pole switch

can be used as the other switch in a 3-way installation.

Pry the switch door open from the

bottom using a small screwdriver.

Ensure the ON/OFF selector is set to

ON.

Reset the switch using a paper clip.

0:00 and MO will flash.

If the display is blank:

•Ensure the ON/OFF selector is prop-

erly engaged in the ON position. Push it to the right using a small

screwdriver.

•If the programmable switch controls a lamp equipped with a built-in

On/Off switch, ensure the lamp switch is set to On.

•Ensure the light bulb is not burned out and is tightly screwed in its socket.

EXISTING 3-WAY INSTALLATION

If either switch does not work properly, rewire the jumper between the

"common" screw and the other screw.

WARNING: Before replacing the light bulb, place the ON/OFF selector in

the OFF position. Failure to do so might damage the switch.

NOTE: The switch displays the time in 24-hour format by default or fol-

lowing a reset.

To change to 12-hour format (or vice versa), proceed as follows:

a)Press one of the control buttons to ensure the MAN or AUTO

indicator is displayed.

b)Press the MIN and HOUR buttons simultaneously and brieftly

(0:00 display = 24-hour, 12:00 display = 12-hour).

Set the time using the HOUR and MIN buttons. If you have selected

the 12-hour format, ensure that PM appears on the screen when an

afternoon time is displayed.

Set the day by using the DAY button.

Press one of the control buttons or close the switch door to return to

normal operation.







 1.







 2.

M38935

Line

Neutral

See NOTE A

120 VAC

Line

Neutral

120 VAC

M38936

Red

120 VAC

Jumper Red 3-wire cable

See NOTE A







 3.







 4.

M38937

120 VACSee NOTE A

M38934

Control (4)

Reset

On/Off selector

Product specificaties