Hikvision DS-KIS102-P Handleiding

Bekijk gratis de handleiding van Hikvision DS-KIS102-P (2 pagina’s), behorend tot de categorie Intercomsysteem. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.7 sterren uit 9 reviews. Heb je een vraag over Hikvision DS-KIS102-P of wil je andere gebruikers van dit product iets vragen? Stel een vraag

DS-KIS102-P/Surface

1

2- WireVideo Intercom Kit

3

2

1

3

2

1

Wiring Diagram 1

Bit 1: outdoor unit address set, “ ” means outdoor unit 1 and

“ ” means outdoor unit 2.

Bit 2: Main cards set, “ ” means normal mode and “ ”

means Add Main Cards mode.

This 2-wire video intercom kit supports maximum system capacity of 2 outdoor units, 3 indoor units and 1 surveillance camera.

It has rich features including intercom, monitoring, unlocking, mute, alarm and so on.

ON

2

1

ON

2

1

ON

2

1

ON

2

1

O

Tampering switch

Outdoor unit

Indoor unit installaon

1. Fix the bracket on the wall with screws. (1.4-1.6m high from the ground )

2. Connect the wires according to the wiring diagram.

3. Hang on the bracket.

4. Connect to power supply.

Outdoor unit installation

Name Plate

Rain shade

Camera

CALL button

Speaker

Microphone

Indoor unit

Installation Instruction

1. Fasten the rain shade on the wall with screws. (1.4-1.6m high from the ground)

2. Connect the wires according to the wiring diagram.

3. Fix into the rain shade and fasten the bottom with screws.

Microphone

Monitor

Lock 1

Lock 2

Talk

MenuButton

Down

Up

Card Reader

Photocell

Analog Camera

(Extension)

External

power supply

DC12V 400mA≤

Electric Lock

Lock1

Snapshot

Exit button

for Lock 2

NOTE: When setting bit 2 to Add Main Cards mode, error

may happen when calling and answering the call.

123456

3

2

1

1234

ON

2

1

O

AC100-240V

50/60Hz

DC 15V

123

VDD

GND

VIDEO

123132

Door

Sensor 1

Door

Sensor 2

Indoor unit

Outdoor unit

DIP switch

Non Polarity

Lock2 (dry contact)

Electric

Lock

Normally open

Power supply

for unlocking

Magnetic

lock

Power supply

for unlocking

Normally closed

≤30V/2A

Exit button

for Lock 1

DIP Switch on the outdoor unit

Bit 1: Main/Sub unit set, slide to ON

position to set it as a main unit.

Bit 2: Turn on/off the coin battery.

NO

NO

1

2

12

NOTE:

For the bit 2, slide to ON position before use.

Otherwise, system will not save the date and

time setting during a power outage. Factory

default set is OFF.

ON

12

3

2

1

3

2

1

Lock2 (dry contact)

Electric

Lock

Normally open

Power supply

for unlocking

Magnetic

lock

Power supply

for unlocking

Normally closed

≤30V/2A

indoor subunit 2#

NOTICES

Turn off the power before wiring.

Aer installaon, if the product doesn't work, check if wires are

connected properly and securely.

Use a slightly damp so cloth to clean the camera or screen.

The outdoor unit must not be directly exposed to sunlight.

If it is unable to unlock, check if wires are connected properly and

securely. Also, make sure the voltage for unlocking is sufficient.

The image quality may be interfered by strong electromagnec

signals, therefore, when using the product, avoid the

electromagnec sources such as motor and transformer and make

sure the circumstance is barrier-free and no interference.

Connecon with 2-Core Cable

123132

Door

Sensor 1

Door

Sensor 2

123456

3

2

1

ON

2

1

A

AC100-240V

50/60Hz

123456

1234

AC100-240V

50/60Hz

3

2

1

ON

2

1

ON

2

1

ON

2

1

DC 15V

DC 15V

B

C

C

1234

123

123

VDD

GND

VIDEO

DIP switch

Lock1

DC 12V ≤400mA

Electric Lock

Lock1

123132

Door

Sensor 1

Door

Sensor 2

Analog Camera

(Extension)

External

power supply

main unit

Outdoor unit1

Outdoor unit2

indoor subunit 1#

123456

1234

AC100-240V

50/60Hz

DC 15V

3

2

1

3

2

1

Lock2 (dry contact)

Electric

Lock

Normally open

Power supply

for unlocking

Magnetic

lock

Power supply

for unlocking

Normally closed

30V/2A≤

A

Press down on the buon, and insert

the wire in the corresponding hole.

Release the buon to clamp the wire

in place. Gently pull the wire

to see if they are clamped ghtly.

3

2

1 8

7

6

5

4

DC 12V ≤400mA

Electric Lock

NOTE: To make system work, the outdoor unit must be

connected to the main indoor unit.

ON

12

ON

12

ON

12

ON

12

ON

12

Exit button

for Lock 2

Exit button

for Lock 1

Bit 1: Main/Sub unit set, slide to

ON position to set it as a main unit.

Bit 2: Turn on/off the coin battery.

NO

NO

1

2

12

Exit button

for Lock 2

Exit button

for Lock 1

. Cable between the outdoor unit and indoor unit:

- 0~15m: RVV2 × 0.5mm²

- 30~50m: RVV2 ×0.75mm²

- 50~100m: RVV2 × 1.0mm² (ONLY suitable for Wiring Diagram 1)

. Cable between indoor units:

- 0~20m: RVV2 × 0.5mm²

- 20~30m: RVV2 × 0.75mm²

. Cable for locks:

- 0~10m: RVV2 × 1.0mm²

Connection with Twisted 2-Core Cable

. Cable between the outdoor unit and indoor unit:

- 0~30m: RVV2 × 0.5mm²

- 30~70m: RVV2 ×0.75mm²

- 70~100m: RVV2 × 1.0mm²

. Cable between indoor units:

- 0~30m: RVV2 × 0.5mm²

- 30~40m: RVV2 × 0.75mm²

. Cable for locks:

0~10m: RVV2 × 1.0mm²

NOTE: The cable with pure copper conductor must be

used. Alloy or other materials will affect the usage.

B

A

B

C

A

B

C

1

2

3

2

3

4

Wiring Diagram 2

4

OVERVIEW

Product specificaties