Heatit HEAE5430498-B Handleiding

Bekijk gratis de handleiding van Heatit HEAE5430498-B (4 pagina’s), behorend tot de categorie ivópalack. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.2 sterren uit 5 reviews. Heb je een vraag over Heatit HEAE5430498-B of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Ver 2016-B

IMPORTANT!

PLEASE READ THIS BEFORE INSTALLATION.

This thermostat is tested and certified by Pepper One Gmbh

according to the requirements put forward by the Z-Wave

Alliance. This is a Z-wave Plus product with the 500 series chip.

If the product does not work with your gateway, then the

gateway manufacturer has not made an integration or

implemented such a thermostat with their gateway.

We do not give any guarantee towards integration.

PRINCIPLES FOR REGULATION

The Heatit Z-Wave thermostat is designed for controlling

electrical heating cables and electrical radiators/convectors.

The thermostat has 2 internal temperature sensors and has

3 algorithms for temperature compensation. After you have

set the temperature, the thermostat will use a hysteresis to

regulate the temperature. The hysteresis is adjustable.

TEMPERATURE SHOWN IN DISPLAY

The temperature shown in the display is the actual temperature

for floor sensor and the external room sensor. You are able to

calibrate the sensor values.

When using the internal room sensor, the temperature shown

is the set point. When using the internal sensor, the thermostat

can seem somewhat inaccurate. This is due to heat generation

inside the thermostat, draft and other external influences.

If the thermostat is to be used with waterbased heating systems,

you have to use an external sensor.

SETUP

This manual describes the most essential functions and

technical specifications of the thermostat. These instructions

help the user to control the thermostat, and the electrician

to install and setup the thermostat.

INSTALLATION

Installation must be done by a qualified electrical installer in

accordance with the National Building codes. Before installation,

disconnect any power to the thermostat’s mains. During

installation of the thermostat, power to the thermostat must

be disconnected AT ALL TIMES!

Use e.g. a small slotted screwdriver. Start by carefully removing

the front cover by pushing the release springs. The front cover

and the frame can now be removed.

Now connect the wires to the thermostat’s terminals:

HEATING (N) Heating cable connection (Neutral)

N Power connection (Neutral) 230V

L Power connection (Live) 230V

HEATING (L) Heating cable connection (Live)

PILOT Pilot signal (ECO temp) 230V

FLOOR SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ).

Default 10kΩ.

EXTERNAL SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ).

Default 10kΩ.

Next, position the thermostat and fasten it onto the wall’s

mounting box using 2-4 screws. Position the frame, then

position and carefully press the front cover until it snaps in

place. Check that the front cover has snapped in place properly

on both left and right side. The front cover should now be firmly

fixed on all sides.

STARTUP

AFTER CONNECTING THE POWER TO THE THERMOSTAT FOR THE

FIRST TIME, ALL PARAMETERS WILL HAVE DEFAULT SETTINGS.

2 yr

HEATITZ-WAVE

Installers manual

Firmware 1.8

01.06.2016

Release spring

1: Left3: Right2: Center

87 mm

58,8 mm

HEATING L

L

N

HEATING N

PILOT WIRE

FLOOR

SENSOR

EXTERNAL

SENSOR

Made in EU

TF 021

21,3 mm

51,1 mm

87 mm

58,8 mm

29,9 mm

Product specificaties