Haws 3612FRBFA Handleiding
Pagina's 13 Niet gecategoriseerd
Bekijk de handleiding van Haws 3612FRBFA gratis online of download de PDF. Deze handleiding is 1 keer bekeken. Vraag over dit model? Stel een vraag
04/03/2025Model3612FRBFA Page 1 of 13
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 3597424-
E-mail:
[email protected] website: www.hawsco.com
No. 0510002057 (3)
MODEL 3612FRBFA
Outdoor Bottle Filler/Drinking Fountain
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS warrants that all ofits products are guaranteed against defective material or poor workmanship for
a period ofThe foregoing notwithstanding, warrants certain one year from the date of shipment. HAWS
specific products or components thereof for an adjusted period. A list of these excepted products and
components and a description of their respective warranty terms may be found here:
www.hawsco.com/warranty. HAWS’ liability under this warranty shall be discharged by furnishing without
charge F.O.B. factory any goods, or part thereof, which shall appear to the Company upon HAWS
inspection to be of defective material or not of firstclass workmanship, provided that a claim is made in -
writing to Company within a reasonable period after receipt of the product. Where claims for defects are
made, the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS shall
not be liable for the cost of repairs, alterations or replacements, or the labor required to implement them, or
for any expense connected therewith made by the owner or owner’s agents, except upon written authority
from . HAWSHAWSshall not be liable for any damages caused by defective materials or poor
workmanship, except for replacements, as provided above. Buyer agrees that has made no other HAWS
warranties either express or implied in addition to those above stated, except that of title with respect to
any of the products or equipment sold hereunder and that shall not be liable for general, special, HAWS
incidental, or consequential damages claimed to arise under the contract of sale.
Equipment manufactured by HAWS is warranted to function if installation and maintenance instructions
provided are adhered to. The units also must be used for the purpose for which they were intended. Any
HAWS emergency equipment is intended to supplement firstaid treatment. Due to widely varying -
conditions, HAWS cannot guarantee that the use of this emergency equipment will prevent serious injury
or the aggravation of existing or prior injuries.
EXCEPT AS EXPRESSLY STATED HEREIN, HAWS HEREBY DISCLAIMS ALL WARRANTIES,
WHETHER EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY MAY NOT BE MODIFIED OR EXTENDED WITHOUT THE
WRITTEN CONSENT OF HAWS. REMEDIES AND REPLACEMENTS STATED HEREIN ARE
EXCLUSIVE. IN NO EVENT SHALL HAWS BE LIABLE FOR ANY SPECIAL, PUNITIVE,
CONSEQUENTIAL OR INCIDENTAL DAMAGES TO ANY PERSON INCLUDING BUT NOT LIMITED
TO DAMAGES FOR LOSS OF USE OR PROFITS, SUBSTITUTE PRODUCTS OR COSTS, PROPERTY
DAMAGE, OR OTHER MONETARY LOSS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT:1--- 8007665612
FOR CUSTOMER SERVICE: 1--- 8886404297
04/03/2025Model3612FRBFA Page 2 of 13
RECOMMENDED TOOLS:
- Measuring Tape
- PVC Pipe Cutter
- Plastic Tubing Cutter
- PVC Solvent Weld Glue
- ¼” Bit-Holding Screwdriver
- Level
- 10” Pipe Wrench
- Adjustable Plier
- 1/8 and 5/32 Tamper Resistant Hex Bits (Supplied)
- 9/16” and 5/8” , 8” Max LengthBox/Open Combination Wrenches
- 3/8” Socket Wrench/Rachet, 8” Max Length
- 9/16” Deep Socket
- 15/16” Socket
LOCATION OF UNIT: The Model 3612FRBFAFreeze Resistant and Dual Bottle Filler
Fountain can be assembled to be installed and ADA accessible by first locating the pedestal
base on a hardscape with dimensions that comply with your local, state, and federal codes
regarding clear floor space and pedestrian protection area. Refer to the last page of this
document for more information.When the right pedestal arm is installed in the high
orientation, and the left pedestal arm is installed in the middle orientation, the height
dimensions shown on the model specification sheet meet current Federal Americans with
Disabilities Act (ADA) wheelchair requirementsThe bottle filler meets ADA requirements for .
either a front approach or a side approach. When installing this unit, local, state and federal
(including ADA) be adhered to.If height other than shown is required, then codes must
dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 3090 psi (2--6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Water supply inlet connection is a 3/8“O.D. fitting. compression
Waste outlet is 1Plumbing connections vary depending on how the unit is -1/2” . PVC pipe
configured during assembly. Please consult the installation drawings below for supply and
waste fitting arrangements and assembly for your specific model.
MAINTENANCE: Refer to 6518FR & 6518.2FROperation and Maintenance Sheets for more
information.
INSTALLATION PROCEDURE
Follow the installation procedures outlined in the installation diagrams for your specific model
below. Note: 3612FRBFAversion must be connected to Haws Model6518FR & 6518.2FR s
freeze resistant bury valves, sold separately. See 6518.2FR seriesinstallation manual s for
instructions.
GENERAL NOTES:
1. For all compression fitting connections, only connect NSF61 copperor plastic -
3/8” outside diameter tubing. The following assembly instructions must be
followed to ensure a watertight connection:
a. Cut tubing square and clean. Deburr if necessary.
b. Place compression nut and ferrule over end of tubing.
c. For plastic tubing (must be ¼” inside diameter), insert supplied tubing
insert into end of tubing.
d. Push tube into the fitting until it bottoms out.
04/03/2025Model3612FRBFA Page 3 of 13
e. Thread nut onto fitting and tighten snugly with 5/8” wrenches.
*For more information about Haws products, see our website:
www.hawsco.com
© 2023 Haws
®
– Corporation All Rights Reserved
HAWS
®
and other trademarks used
in these materials are the exclusive property of Haws Corporation.
Tube Sizes
O.D.
Tolerance
Insertion Depth
3/8”
±.005”
3/4”
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1.
Insufficient bubbler flow (From
Drinking Fountain)
1a.
Check that inlet screwdriver stop valve
is wide open (Not Supplied).
b.
Verify minimum 30 psi flowing supply
pressure.
c.
Adjust valve to increase flow. See
6518FR or 6518.2FR Manual*.
2.
Insufficient bottle filler flow
2a.
b.
c.
c.
Check that inlet screwdriver stop valve
is wide open (Not Supplied).
Verify minimum 30 psi flowing supply
pressure.
Nozzle strainer is clogged. Use nozzle
removal tool to remove strainer and
replace. Replacement strainers may be
ordered by calling Customer Service.
Adjust valve to increase flow. See
6518FR or 6518.2FR Manual.*
Product specificaties
| Merk: | Haws |
| Categorie: | Niet gecategoriseerd |
| Model: | 3612FRBFA |
Heb je hulp nodig?
Als je hulp nodig hebt met Haws 3612FRBFA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden