Gigaset AS200 Trio Handleiding

Bekijk gratis de handleiding van Gigaset AS200 Trio (4 pagina’s), behorend tot de categorie Telefoon. Deze gids werd als nuttig beoordeeld door 55 mensen en kreeg gemiddeld 4.1 sterren uit 2 reviews. Heb je een vraag over Gigaset AS200 Trio of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Gigaset AS200-AS200A-AS300_AS300A_UK _ A31008-M2208-L101-2-7619

Quick start guide

AS200 - AS200A

AS300 - AS300A

GIGASET. INSPIRING CONVERSATION.

GIGASET HELPLINE: 0845 3670812

Pack contents

If you have purchased a model

with multiple handsets the

package should contain two

batteries, a battery cover, a

charging cradle 8 with mains

adapter 9 for each additional

handset.

1

1one Gigaset AS200/AS200A/AS300/AS300A Base station

2one mains adapter

3one Gigaset AS200H/AS300H handset

4one phone cord

5two batteries

AS185

GIGAS ET . INS PIRING C ONVERSA T ION.

2

3

45

7

6

6one battery cover

7this Quick start guide

or

8 9

Connecting the base station

¤Connect power adapter 1 and

Phone jack 2 to the base and

place the cable recesses.

Please ensure the power lead is

fully inserted.

Please note:

uThe mains adapter must always be connected, as the Phone will not operate

without a mains connection.

uAlways use the power adapter and Phone cord supplied. Pin connections on

Telephone cables can vary.

Connecting the charging cradle (if included)

1

1

1

2

¤Plug the mains adapter into the

plug socket2.

¤Connect the flat plug from the

mains adapter 1.

If you need to disconnect the plug from the

charging cradle, press the release button 3and

disconnect the plug 4.

1

2

4

3

Preparing the handset

Initial charging and discharging of the batteries

¤

Insert the batteries the right way

round. The polarity is indicated

in/on the battery compartment.

¤Then slide the battery cover back

into the main casing until it clicks

into place.

If you need to open the battery cover, for

instance to replace the batteries, place

your fingertip in the grooved area on the

top of the cover and slide down.

The correct charge status can only be displayed if

the batteries are first fully charged and discharged.

¤Place the handset in the charger

for 7hours.

7h

Then remove the handset from the charger, make and receive Phone calls, setup the

Phone etc. and do not put it on the charger until the batteries are fully discharged.

Setting the date and time

Set the date and time so that the correct date and time can be assigned to incoming

calls, and so that the alarm can be used.

Date: DD:MM:YY

“T OK

INT MENU

¤Press the key below MENU on the

display screen to open the main

menu.

Date/Time

“OK

¤Press the bottom of the control

key ...

... until the Settings menu item

appears.

¤Press the key below OK on the

display screen to confirm your

selection.

The Date/Time menu item appears on

the display.

¤Press the key below OK on the

display screen to open the input

field.

Settings

“OK

¤The active cursor position is flashing.

Enter day, month and year as an

6-digit number via the handset,

e.g. Q11Q1Q for 01/10/10.

Message indication

Message Indication Key ‘ on handset will flash to indicate one or all of the

following events:

umissed calls (if caller ID is enabled for your line numbers will be shown)

unew messages on the answer machine (AS200A/AS300A only)

Activating/deactivating the answer machine (AS200A/AS300A only)

MENU ¢Voice Mail ¢OK ¢Answer Mach. ¢OK (‰= on)

If the answer machine is activated, the answer machine icon ± will be displayed in

the header.

To retrieve your messages, just press the flashing ‘ key on your handset.

Dial tone

The dial tone will only be heard when pressing the c call button for 2 seconds.

A short press will open the redial list.

You can also use the

d

speaker button (AS300/AS300A only).

Display in idle status

u2: internal number, if more then one handset is registered

u±: answer machine is activated (AS200A/AS300A only)

uBattery charge status:

–= e VU (empty to full)

–= flashes: batteries almost empty

–eV Uflashes: charging procedure

Registration handset

Your handsets should already be registered by default, if your handset is flashing the

text "No Base" then it can be that:

uYour base station is not switched on, please check if the power supply is connected

properly.

uThere is too much distance between the handset and base.

uYour handset has not been pre-registered in the factory.

In the case that the handset has not been pre-registered, or you want to register an

additional handset to your base station, use the manual registration procedure

below.

Automatic registering procedure

Manual registration procedure

1. On the handset:

MENU ¢Settings ¢OK ¢Handset ¢OK ¢Register HS ¢OK ¢enter the

system PIN for the base and press OK. Default PIN = 0000

2. On the base station:

Within 60 seconds of entering the system PIN, press and hold the registration/paging

key (min. 3 seconds). Registration takes approx. 1 minute.

You can register up to fourhandsets to your base. You can also register other Gigaset

handsets and handsets from other devices with GAP functionality.

V

Put into base

MENU

V

Put into base

MENU

Place the handset with the

display facing up in the base

station.

The handset registers

automatically. Registration

can take up to 5 minutes.

Do not remove the handset

from the base station during

this time.

V

Put into base

MENU

V

Registering

Frequently asked questions

Q:There is no dial tone.

A:Press call button for 2 seconds (long press) to obtain dial tone.

A short press opens the redial list.

Q:The line is crackling / not clear.

A:Have you used the new line cable provided? Please do not use an old cable.

Q:The display is not clear / seems to be broken.

A:The display is protected by a plastic film, please make sure you have removed

the protective film.

Q:The handset is not registered.

A:If your handset is not registered, please follow the Registration handset procedure.

(Described on this page)

Q:The caller ID is not working.

A:Have you subscribed to this service (CLIP) from your provider?

Q:Message indicator flashing and I cannot retrieve my message.

A:Message indicator will flash to indicate missed calls. (Described on this page)

Please check:

Have you used the phone cord supplied

Have you fully inserted the power cable into the base station

Have you inserted the batteries correctly

Have you charged the batteries for 7 hours

Have you set up the Date/Time

To download the latest manuals, visit our web-site: http://www.gigaset.com

You have questions? As a Gigaset customer, you can take advantage of our comprehensive

service offerings. You can find help quickly in this User Manual and in the service pages of

our Gigaset online portal: http://www.gigaset.com

Product may not be fully compatible with the national telephone network. It is clearly

specified on the box near the CE mark for which country/countries the equipment has been

developed. If the equipment is used in a manner inconsistent with this advice or with the

instructions of the manual and on the product itself, this may have implications on the

conditions for warranty or guarantee claims (repair or exchange of product).

In order to make use of the warranty, the product purchaser is asked to submit a receipt

which proves the date of purchase (date from which the warranty period starts) and the

type of goods that have been purchased.

If you have problems setting up or operation this product please call

GIGASET UK HELPLINE 0845 3670812

GIGASET IRL HELPLINE 1850 777277

Product specificaties