GeoVision GV-R1352 Handleiding

GeoVision Toegangscontrolesysteem GV-R1352

Lees hieronder de 📖 handleiding in het Nederlandse voor GeoVision GV-R1352 (21 pagina's) in de categorie Toegangscontrolesysteem. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/21

GV-RK1352 and GV-R1352 Card Reader

The GV-RK1352 and GV-R1352 are card readers designed to recognize identifications cards.

GV-RK1352 comes with keypad, allowing it to also recognize PIN codes. Featured with the

Wiegand and RS-485 outputs, the readers can be connected to any standard access control

panel. The readers are protected by a weather sealed and IP66 compliant housing for

outdoor use.

The content of this installation guide refers to the following readers:

• GV-RK1352 firmware V1.2

• GV-R1352 firmware V1.2

Packing List

GV-RK1352

1. GV-RK1352 Card Reader

2. Screw x 2

3. Screw Anchor x 2

4. Front Cover Plate x 2

Front View

GV-R1352

February 6, 2015

1. GV-R1352 Card Reader

2. Screw x 3

3. Screw Anchor x 2

4. Security Torx

Front View

1. Physical Descriptions

1.1 Electric Wire

GV-RK1352

Wire Color Function

Red DC 7.5 ~ 12 V

Black GND

Yellow Beeper

Orange Green LED

Light Red Red LED

Green Wiegand Data 0

White Wiegand Data 1

Blue RS-485 +

Light Blue RS-485 -

Rear View

GV-R1352

Wire Color Function

Red DC 7.5 ~ 12V

Black GND

Yellow Beeper

Orange Green LED

Light Red Red LED

Green Wiegand Data 0

White Wiegand Data 1

Blue RS-485 +

Light Blue RS-485 -

Gray N/A

Purple N/A

Brown N/A Rear View

February 6, 2015

1.2 Keypad (GV-RK1352 Only)

When accessing an entry using GV-RK1352, you can enter the door’s PIN code on the

keypad or present the card and then enter the card’s PIN code on the keypad to be granted

access. The access mode is defined on GV-ASManager.

1. 0~9 Number Keys: Press the number keys to enter the PIN code.

2. # Key: Press the # key to confirm the PIN code.

3. ﹡

﹡

﹡﹡Key: Press the ﹡key to cancel the PIN code.

1.3 LED Indicator and Beeper

In standby mode, the LED is blue. When a card is read, the LED flashes green and the

beeper beeps once.

The reader comes with external control wires for Green LED, Red LED and Beeper. You can

connect these control wires to a GV-AS Controller to change the default settings of the LED

and Beeper. For details on how to configure the settings, refer to 5. Changing the Settings of

Beeper and LED later in this installation guide.

Note: You can only connect the LED and beeper wires to GV-AS210 / 2110 / 400 / 410 /

4110 / 810 / 8110.

February 6, 2015

Product specificaties

Merk:	GeoVision
Categorie:	Toegangscontrolesysteem
Model:	GV-R1352
Kleur van het product:	Zwart
Gewicht:	120 g
Certificering:	CE, FCC, RoHS
Frequentie:	13.56 MHz
Afmetingen (B x D x H):	65.80 x 20.5 x 115.6 mm
Bedrijfstemperatuur (T-T):	-30 - 65 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent