GE UXADJB36PSS Handleiding

GE Niet gecategoriseerd UXADJB36PSS

Lees hieronder de 📖 handleiding in het Nederlandse voor GE UXADJB36PSS (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
UXADJB36PSS, UXADJB48PSS
30” to 36” Adjustable Backsplash
WARNING To prevent ignition of combustible
materials, the entire back wall above the range
must be protected by a backsplash constructed of
non-combustible material.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT Save these instructions
for local inspector’s use.
IMPORTANT Observe all governing
codes and ordinances.
IMPORTANT Remove all packing
material and literature from oven before connecting
gas and electrical supply to range.
Note to Installer Be sure to leave these
instructions with the consumer.
Note to Consumer Keep these instructions with
your Owner’s Manual for future reference.
This backsplash adjusts to fit the space between the
top of the range and the bottom of the hood, from
30” Min. to 36” Max. height.
Maximum shelf load-bearing weight is 40 lbs.
Installation
Instructions
TOOLS AND MATERIALS REQUIRED
■Glovestoprotectagainstsharpedges
■T-15and#2Phillipsscrewdrivers
■Drillwith3/32”and9/64”bits
■Safetyglasses
■Level
■Pencil
This Kit Includes
■Topwallsupport
■Bottomwallsupport
■Topcoverwithshelf
■Bottomcover
TOOLS AND MATERIALS REQUIRED
(Cont.)
■Hardwarepackagewith
 –9StainlessSteelTorx15
#8self-tappingscrews
 –9Phillips#2panheadwood#10screws
 –3StainlessSteel#2trusshead#10screws(for
alternate installation method)
Hardware
Package
Top Cover
with Shelf
Bottom Cover
Bottom Wall Support
Top Wall
Support
INSTALL THE WALL SUPPORT PANELS
WARNING The wall support panels must be
securely fastened to the wall. Failure to do so could
result in damage or personal injury.
IMPORTANT: This backsplash is designed to cover
the wall between the bottom of the hood and the top of
the range. The vent hood should be installed over the
rangetop or range before installing this backsplash.
■InstallandleveltheRange/Rangetopaccordingto
the product installation instructions.
■Removebacksplashpackagingandprotectivefilm.
■Locatewallstudsoneachside.Wherestudsarenot
available,plantousewallanchors(notprovided).
■Usealeveltopencil2horizontallinesonthewall,
one1/8”belowtheventhoodandtheother1/8”
abovetheRange/Rangetop.This1/8”spaceallows
the cover panels to overlap the wall supports.
■Securethetopwallsupportpaneltothewallwith4
wood screws, through the outermost studs.
■Use4woodscrewstosecurethebottomwallsupport
panel. The center slot should be positioned at the top.
The gap between the top and bottom support panels
will be covered by the top cover with shelf.
1/8”
Secure the
top panel
to the wall
with 4 wood
screws
1/8”
Secure the
bottom panel
to the wall
with 4 wood
screws
Wood
Screws
Center
Arrow
Wood
Screws
31-10692-101-18GEA
231-10692-1
UXADJB36PSS, UXADJB48PSS Accessory Installation
INSTALL COVER PANELS
See alternate method if side access is blocked.
■Holdthebottomcoveroverthebottomsupport
whiledrivingonescrew(provided)intoeachside.
■Placethetopcoverwithshelfoverthetopwall
support.Ifyouhaveaccesstothesides,securethe
panel with two screws on each side.
■Securethetopcoverwithshelftothetopsupport
with screws through the front of the panel, at the top
corners.Useonescrewoneachside.
INSTALL COVER PANELS (cont.)
ALTERNATE METHOD: When side access is blocked
■Installbottomcoveroverthebottomsupportwhile
driving one screw into each side.
■Holdtopcoverinplacewhilemarkingscrewlocations,
just below shelf support and onto bottom cover.
■Removetheshelfanddrilla9/64”diameterholein
the pencil-marked locations.
■Mountthetopcoveroverthetopsupportand
secure the front cover with screws through the
drilled holes on each side.
■Installscrewsthrougheachtopcorner.
Install
Screw
CoverPanel
Install
Screw
InstallCornerScrews
Mark Screw
Locationsfor
Alternate Method
InstallScrew
onEachSide
Shelf
InstallScrewinTopCorneronEachSide
31-10692-1 3
UXADJB36PSS, UXADJB48PSS
Dosseret ajustable 30” à 36”
AVERTISSEMENT Afin d’éviter que les matériaux
inflammables ne prennent feu, la totalité de la surface du
mur se trouvant au-dessus de la cuisinière doit être protégée
par un dosseret ignifuge.
AVANT DE COMMENCER
Lisez attentivement l’ensemble des consignes.
IMPORTANT Conservez ces instructions
pour l’inspecteur local.
IMPORTANT Respectez toutes les normes
ainsi que les recommandations préconisées par les
autorités compétentes.
IMPORTANT Retirez tout le matériel
d’emballage et la documentation dans le four avant de
raccorder les alimentationsen gaz et électrique à la cuisinière.
Remarque à l’attention de l’installateur BAssurez-
vous de laisser ces instructions au consommateur.
■ Note au consommateur Gardez ces instructions avec
votre manuel d’utilisation pour férence ultérieure.
■ Cedosseretestconçucomblerl’espaceentrelehaut
delacuisinièreetlebasdelahotte,entreunehauteur
maximale de 76 cm et 91 cm.
■ Lepoidsmaximaldeportancedel’étagèreestde18kg.
Instructions
d’installation
INSTALLEZ LES PANNEAUX DE
SUPPORT MURAL
AVERTISSEMENT Lespanneauxdesupportmural
doivent être correctement fixés au mur afin d’éviter toute
blessure ou dommage matériel.
IMPORTANT :Cedosseretestconçupourcouvrirlemur
entre la partie supérieure de la cuisinière et la partie inférieure
delahotte.Lahotted’extractiondoitêtreinstalléesurlatable
de cuisson ou de la cuisinière avant d’installer le dosseret.
■ Installezetajustezlapositiondelatabledecuisson/
cuisinière conformément aux consignes d’installation.
■ Retirezl’emballagedudosseretetlefilmprotecteur.
■ Localisezlespoteauxmurauxsurchaquecôté.En
l’absencedepoteaux,utilisezplutôtdeschevillesmurales
(non fournies).
■ Utilisezunniveaupourtraceraucrayon2lignes
horizontalessurlemur,uneà1/8”souslahotte
d’extractionetl’autreà1/8”au-dessusdelatablede
caisson/cuisinière.Cetespacede1/8”faitquelepanneau
de recouvrement se superpose aux supports muraux.
■ Fixezlepanneaumuralsupérieuraumuràl’aidede4vis
à bois, à travers les poteaux externes.
■ Utilisez4visàboispourfixersupportmuralinférieur.La
rainurecentraledoitêtreplacéeenhaut.
L’espaceséparantlepanneaudesupportdubasdecelui
duhautseracombléparlaplaquesupérieuravecétagère.
OUTILS ET MATÉRIEL NÉCESSAIRES
■ Gantspourvousprotégerdespartiestranchantes
■ Tourneviscruciforme2etT-15
■ Percezavecdesforets23mm
(3/32”)et35mm(9/64”)
■ Lunettesprotectrices
■ Niveau
■ Crayon
Ce Kit comprend
■Panneaudesupportmural
■ Panneaumurinférieur
■Panneausupérieur
avec étagére
■ Plaqueinférieure
OUTILS ET MATÉRIEL NÉCESSAIRES
(suite)
■ Sachetdematérielcontenant
9 vis autotaraudeuses à 6 lobes
internesenacierinoxydable15,no8
 –9visàtecylindriquebombéeno2pourboisno10
 –3visàtebombéeno2enacierinoxydableno10
(pouruneméthoded’installationalternative)
Panneau
supérieur
avec étagère
Plaqueinférieure
Supportmuralinférieure
Supportmural
supérieur
Sachet
de matériel
31 mm
(1/8”)
31 mm
(1/8”)
Vis à
bois
Flèche
centrale
Vis à
bois
Fixezle
panneau
supérieur au
muravec4
vis à bois
Fixezle
panneau
inférieur au
muravec4
vis à bois


Product specificaties

Merk: GE
Categorie: Niet gecategoriseerd
Model: UXADJB36PSS

Heb je hulp nodig?

Als je hulp nodig hebt met GE UXADJB36PSS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd GE

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd