GBC HeatSeal H600 Pro Handleiding

GBC Lamineersysteem HeatSeal H600 Pro

Lees hieronder de 📖 handleiding in het Nederlandse voor GBC HeatSeal H600 Pro (8 pagina's) in de categorie Lamineersysteem. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

General Binding Corporation

Northbrook, IL 60062-4195

13 PRO Operating Instructions. . . . . . . . . . 2

Manuel d’Utilisation . . . . . . . . . . . . 3

Manual de Utilización . . . . . . . . . . 5

Operating Instructions

IMPORTANT SAFETY INSTRUCTIONS

YOUR SAFETY AS WELL AS THE SAFETY

OF OTHERS IS IMPORTANT TO US. IN THIS

INSTRUCTION MANUAL AND ON THE

PRODUCT ARE IMPORTANT SAFETY

MESSAGES. READ THESE MESSAGES

CAREFULLY.

THE SAFETY ALERT SYMBOL PRE-

CEDES EACH SAFETY MESSAGE IN

THIS INSTRUCTION MANUAL.THIS SYMBOL

INDICATES A POTENTIAL PERSONAL SAFE-

TY HAZARD THAT COULD HURT YOU OR

OTHERS, AS WELL AS CAUSE PRODUCT

DAMAGE OR PROPERTY DAMAGE.

THE FOLLOWING WARNING IS FOUND ON

THE BOTTOM OF THE PRODUCT.

This safety message means that you could

be seriously hurt or killed if you open the

product and expose yourself to hazardous

voltage.

IMPORTANT SAFEGUARDS

WARNING: FOR YOUR PROTECTION

DO NOT CONNECT THE POUCH

LAMINATOR TO ELECTRICAL POWER

UNTIL YOU READ THESE INSTRUCTIONS

COMPLETELY. KEEP THESE INSTRUCTIONS

IN A CONVENIENT LOCATION FOR FUTURE

REFERENCE. TO GUARD AGAINST INJURY,

THE FOLLOWING BASIC SAFETY PRECAU-

TIONS MUST BE OBSERVED IN THE SET-UP

AND USE OF THIS PRODUCT.

GENERAL SAFEGUARDS

•Use the pouch laminator only for its

intended purpose of laminating

documents according to the indicated

specifications.

•Do not place anything in the throat

opening of the machine other than

carriers with pouches/documents.

•Place unit on a secure, stable work area

to prevent the machine falling and

possibly causing personal injury and

damage to the unit.

•Turn unit off when not in use for an

extended period of time.

•Follow all warnings and instructions

marked on the product.

ELECTRICAL SAFEGUARDS

•The pouch laminator must be connected

to a supply voltage corresponding to the

electrical rating of the machine as

indicated.

•Unplug the pouch laminator before

moving it, or when it is not in use for an

extended period of time.

•Do not operate with a damaged supply

cord or plug, after it malfunctions, or after

it has been damaged in any manner.

•Do not overload electrical outlets beyond

their capacity as this can result in fire or

electrical shock.

•Do not alter attachment plug. Plug is

configured for the appropriate electrical

supply.

•The unit is intended for indoor use only.

•Never push objects into this product

through cabinet slots. Do not spill liquid of

any kind on this product.

SERVICE

•Do not attempt to service or repair the

pouch laminator yourself. Unplug the unit

and contact an authorized service

representative for any required repairs.

CLEANING

CAUTION: Unplug this product before

cleaning.

•Wipe exterior only with a damp cloth. Do

not use detergents or solvents.

OPERATION

Control Panel LCD. The following

information is displayed on the LCD:

READY - Indicates that the machine is at the

requested laminating temperature.

TEMPERATURE - The numbers directly

below the word TEMPERATURE indicate the

user requested temperature setting.

SPEED - The numbers directly below the

word SPEED indicate the speed setting.

Selecting Functions. Pressing keys

performs functions as follows:

Low - Sets the machine to 230°F (110°C),

speed 5

Mid - Sets the machine to 266°F (130°C),

speed 3.

High - Sets the machine to 302°F (150°C)

speed 3.

Note: Use of a carrier is recommended with

all films for better quality output and

protection of rollers.

PRE/H - Sets the machine to 176˚ ˚ F (80 C),

Speed 2, stand-by.

MEAS - Measures the current machine

temperature.

COLD - This is the setting that is

automatically selected when the machine is

first turned on. Sets the machine to 0, no

temperature and no speed. If the

temperature of the heater platen is above 90˚

C (194 F), then speed ˚ “2” is automatically

set to protect the rollers.

TEMPERATURE -These keys are used to

increase or decrease temperature by

1˚F. Temperature can be adjusted up

to 160 C or 320˚ ˚ F.

SPEED - Adjust the speed of the rollers.

Speed 6 is the fastest speed.

STOP - Stops the revolution of the rollers. To

protect the rollers, the machine should not be

stopped for long periods of time when the

temperature is above 90 C (194˚ ˚ F).

REV - Reverses the revolution of the

rollers to correct misfeeds.

SET-UP

1. Connect power cord to appropriate power

source.

2. Push the power switch located on the back

of the machine to the “on” position.

HOT LAMINATION

After the laminator has been turned on using

the power switch located on the back of the

machine, the Cold mode is automatically set.

“Ready,” temperature setting “0” and speed

setting “ ”0 should be displayed on the LCD.

1. Select either “LOW, MID, or HIGH”

function key. The LCD will indicate the

temperature and speed selected. “Ready”

will not be indicated until the laminator

has reached the set temperature.

2. Use the Laminating Guide included with

the machine to select the proper tempera-

ture and speed for the material to be

laminated.

3. Center the item to be laminated into a

laminating pouch, so that the borders are

even on all sides.

4. Insert the pouch with the item sealed-edge

first into the paper CARRIER that is includ-

ed with each carton of pouches. Position

the sealed edge of the pouch against the

inside folded edge of the carrier.

5. Insert the carrier and its contents straight

into the machine, leading with the folded

edge. handle carriers carefully so that

they can be reused.

WARNING

Electrical shock hazard. Do not

open. No user servicable parts

inside. Refer servicing to

qualified service personnel.

13 Pro

REV

Selecting

Functions

}

Control

Panel

LCD

INSTRUCTIONS CONCERNANT

LA SECURITE

VOTRE SÉCURITÉ, COMME CELLE

DES AUTRES, EST IMPORTANTE

POUR NOUS. CES INSTRUCTIONS

CONTIENNENT D'IMPORTANTS MESSAGES

RELATIFS À LA SÉCURITÉ. MERCI DE LES

LIRE TRÈS ATTENTIVEMENT.

CE SYMBOLE “ATTENTION SÉCURITÉ”

PRÉCÈDE, DANS CE MANUEL D'UTILISA-

TION, CHAQUE MESSAGE CONCERNANT

LA SÉCURITÉ. CE SYMBOLE INDIQUE UN

RISQUE POTENTIEL DE BLESSURE POUR

VOUS OU D'AUTRES PERSONNES, OU UN

RISQUE DE DOMMAGE POUR LA MACHINE

OU VOS BIENS PERSONNELS.

L’AVERTISSEMENT SUIVANT EST NOTIFIÉ

SUR LA PARTIE INFÉRIEURE DE

L’APPAREIL.

Ce message signifie que vous pourriez être

très sérieusement blessé si vous tentiez

d’ouvrir l'appareil en vous exposant ainsi à

un risque de choc électrique.

INSTRUCTIONS CONCERNANT

LA SECURITE

ATTENTION: PAR MESURE DE

SÉCURITÉ, NE BRANCHEZ PAS LA

PLASTIFIEUSE À POCHETTES AVANT

D'AVOIR LU EN TOTALITÉ CES INSTRUC-

TIONS. CONSERVEZ LES DANS UN

ENDROIT APPROPRIÉ AFIN DE POUVOIR

VOUS Y RÉFÉRER SI NÉCESSAIRE. AFIN

D'ÉVITER TOUTE BLESSURE, LES

PRÉCAUTIONS DE BASE SUIVANTES

DOIVENT ÊTRE OBSERVÉES À

L'INSTALLATION ET LORS DE

L'UTILISATION DE CET APPAREIL.

MESURES DE SECURITE GENERALES

• ’N utilisez la plastifieuse à pochettes que

pour la plastification de documents en

vous conformant aux spécifications

indiqu es.é

• ’N introduisez pas dans la fente

d'alimentation de la machine autre chose

que des transporteurs, des pochettes et

des documents.

• é é Installez la machine en s curit sur un

emplacement stable pour viter qué ’elle

ne tombe; cela pourrait l'endommager et

causer d' ventuelles blessuresé

corporelles aux utilisateurs.

6 The laminated item will automatically exit

the rear of the pouch laminator. After the

pouch has stopped moving, place the

carrier on a flat surface to cool briefly

before removing the finished pouch.

7. If the laminated product looks hazy, then

the temperature may need to be

increased or the speed decreased. If the

laminated product looks wavy, then the

temperature may need to be decreased

or the speed increased.

8. Select PRE/H to keep the machine on

stand-by at 80 C (176˚ ˚ F).

9. If finished laminating, press the “COLD”

key. Temperature 0 and Speed 2 will be

displayed. When the temperature

reaches 85 C (186˚ ˚ F) the rollers will

stop automatically. Cooling down the

machine before turning off the power

switch protects and extends the life of the

rollers.

10.Turn off the power switch.

11. Unplug the power cord if the machine will

not be used for a long period of time.

OPERATION, COLD LAMINATION

After the laminator has been turned on using

the power switch located on the back of the

machine, the Cold mode is automatically set.

“Ready,” temperature setting “0” and speed

setting “ ”0 should be displayed on the LCD.

If the machine has just recently been used

for Hot Lamination, then the machine must

reach a temperature of no hotter than 30˚ C

(86˚ F) before starting Cold Lamination.

1. Select a GBC No-Heat Laminate that is

slightly larger than the document to be

laminated.

2. Run the film, film-side faced up, for about

3-6mm (1/8 - 1/4 ) into the laminator, and”

then press STOP to stop the rollers.

3. Carefully separate the backing release

paper from the film, and drape the clear

film over the top of the laminator.

4. Place the document between the

separated film and backing, and select

Speed 1.

5. After the laminated document exits the

rear of the laminator, then either cut off

the excess pouch edge for a flush-cut

appearance, or leave the

edge as an adhesive

border for signage.

OTHER APPLICATIONS

GBC CREATIVE FOILS™

1. Select 150 C (302 F) and speed 3, and˚ ˚

wait for the READY indicator.

2. Place GBC Creative Foil color-side-out

over output from a toner-based laser

printer or photocopier. When printing

various colors on the same original piece,

arrange the different colors and secure

with the stickers included with the

Creative Foils.

3. Insert the document and foil into a carrier

and laminate.

4. When the item exits the rear of the lami-

nator, then remove the document from

the carrier and remove the excess foil.

GBC SOFT TOUCH POUCHES™

1. Select 130 C (266 F) and speed 3, and˚ ˚

wait for the READY indicator.

2. Start laminating.

3. When the pouch exits the rear of the

laminator, carefully rub a finger against a

front corner to remove the protective

carrier film.

ATTENTION

Risque de secousse électrique.

Ne pas ouvrir. Aucune piéce

réparable par l'utilisateur.

Entretien par personnel qualifié.

Manuel d’Utilisation

13 Pro Operating Instructions

GBC Creative Foils™

GBC Soft Touch Pouches™

PRE/H Stand-by

backing release paper

document

lm draped

over laminator

Cold

Lamination

Cold Lamination with

GBC No-Heat Laminate™

Product specificaties

Merk:	GBC
Categorie:	Lamineersysteem
Model:	HeatSeal H600 Pro
Soort bediening:	Knoppen
Kleur van het product:	Grijs
Ingebouwd display:	Ja
Breedte:	692.15 mm
Diepte:	282.7 mm
Hoogte:	419.1 mm
Aantal rollers:	4
Type beeldscherm:	LCD
Voorverwarmingstijd:	- min
Lamineersnelheid:	- mm/min
Maximale lamineerbreedte:	330.2 mm
Maximale dikte document:	0.254 mm