Garmin GT34UHD-TM Handleiding

Garmin Niet gecategoriseerd GT34UHD-TM

Lees hieronder de 📖 handleiding in het Nederlandse voor Garmin GT34UHD-TM (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 152 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

TRANSOM/TROLLING MOUNT

TRANSDUCER

INSTALLATION

INSTRUCTIONS

Important Safety Information

WARNING

See the guide in the Important Safety and Product Information

chartplotter or fishfinder product box for product warnings and

other important information.

You are responsible for the safe and prudent operation of your

vessel. Sonar is a tool that enhances your awareness of the

water beneath your boat. It does not relieve you of the

responsibility of observing the water around your boat as you

navigate.

CAUTION

Failure to install and maintain this equipment in accordance with

these instructions could result in damage or injury.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

To obtain the best performance and to avoid damage to your

boat, you must install the Garmin® device according to these

instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation, go

to for more information.support.garmin.com

Software Update

You must update the Garmin chartplotter software when you

install this device.

If your chartplotter has Wi Fi‑® technology, you should update the

software using the ActiveCaptain® app on a compatible Android

™

or Apple® device.

If your chartplotter does not have Wi Fi technology, you should ‑

update the software using a memory card and a Windows® or

Mac® computer.

For more information, go to .support.garmin.com

Tools Needed

• Drill and drill bits

• Number 2 Phillips screwdriver

• Masking tape

• Marine sealant

Mounting Consideration

To ensure peak performance with the lowest noise and

interference, you should route the transducer cable away from

ignition wires, house batteries and wires, trolling motor batteries

and wires, and high-energy wires such as radar, audio amplifier,

and autopilot pump wires.

Preparing the Transducer for Long-Term Exposure to

Water

NOTICE

Do not use acetone or acetone-based products on the

transducer. Acetone damages the plastic transducer housing.

When you install a transducer on a boat that spends a

significant amount of time in the water, you should coat the

transducer and mounting hardware with a water-based anti-

fouling paint to prevent marine growth.

1Lightly sand the transducer and mounting hardware with a

fine-grit abrasive pad.

2Wipe the transducer and mounting hardware with isopropyl

alcohol.

3Apply water-based anti-fouling paint to the transducer and

mounting hardware.

Installing the Transducer on a Transom

Mounting Location Considerations

• The transducer should be mounted parallel to the water line.

• The transducer should be mounted as close to the center of

the boat as possible.

• If your propeller moves clockwise when the boat moves, the

transducer should be mounted on the starboard side.

• If your propeller moves counter-clockwise when the boat

moves, the transducer should be mounted on the port side.

• The transducer should not be mounted behind strakes, struts,

fittings, water intake or discharge ports, or anything that

creates air bubbles or causes the water to become turbulent.

The transducer must be in clean (non-turbulent) water for

optimal performance.

• The transducer should not be mounted in a location where it

might be jarred when launching, hauling, or storing.

• On single-drive boats, the transducer must not be mounted in

the path of the propeller.

The transducer can cause cavitation that can degrade the

performance of the boat and damage the propeller.

• On boats with outboard or inboard/outboard motors, the

transducer should be mounted at least 38 cm (15 in.) from

the propeller.

• On twin-drive boats, the transducer should be mounted

between the drives, if possible.

Assembling the Transducer with a Transom Mount

Bracket

1 Attach the mount to the transducer with the included

star washers , and screws .

GUID-D3F0E62E-688B-4A6E-B061-D35EB013F5FB v1February 2020

2 Attach the mount to the bracket with the bolt , rubber

washer , flat washer , and lock nut .

NOTE: The bolt should be tight enough to hold the

transducer in place when the boat moves at high speed, but

loose enough to allow the transducer to pivot out of the way if

the transducer hits an obstruction.

Installing the Transom-Mount Hardware

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid cracking in the gel-coat layer when the screws are

tightened.

The cables connected to the transducer should not be cut,

because cutting the transducer cables voids your warranty.

1Cut out the template.

2 With the template aligned vertically on the transom at the

installation location ( ), place Mounting Consideration, page 1

the bottom corner of the template on the edge of the

transom.

3Mark the center location of the two holes of the template.

4Remove the template from the transom.

5Wrap a piece of tape around a 4 mm (

5/32 in.) bit at 18 mm

(7/10 in.) from the point of the bit, to avoid drilling the pilot

holes too deep.

6If you are installing the bracket on fiberglass, place a piece of

tape over the pilot-hole location to reduce cracking of the gel

coat.

7Using the 4 mm (5/32 in.) bit, drill the pilot holes approximately

18 mm (7/10 in.) deep at the marked locations.

8Apply marine sealant to the included 20 mm screws, and

attach the transducer assembly to the transom.

9Route the cable under the transom mount cable hook.

10If you must route the cable through the transom, choose a

pilot-hole location well above the waterline and mark it.

11Place a cable clamp on the transducer cable, approximately

halfway between the transducer and the top of the transom or

the pass-through pilot hole.

12Mark the pilot-hole location for the cable clamp, and using a

3.2 mm (1/8 in.) bit, drill a pilot hole approximately 10 mm

(3/8 in.) deep.

13Apply marine sealant to the included 12 mm screw, and

attach the cable clamp to the transom.

14If you marked a pilot hole in step 7, choose the appropriate

drill bit to drill a pass-through hole completely through the

transom:

• If you have the 4-pin cable, use a 16 mm (

5/8 in.) drill bit.

• If you have the 8-pin or 12-pin cable, use a 25 mm (1 in.)

drill bit.

15Route the transducer cable to the sounder:

• If you are routing the cable using a pass-through hole,

push it through the pass-through hole, and install the

cable-entry cover (Installing the Cable-Entry Cover,

page 2).

• If you are not routing the cable using a pass-through hole,

route the cable up and over the top of the transom.

You should avoid routing the cable close to electrical wires or

other sources of electrical interference.

Installing the Cable-Entry Cover

If you routed the cable through the transom after you installed

the transducer, you should install the cable-entry cover to keep

water from entering your boat.

1 Place the cable-entry cover over the hole and the cable,

with the opening pointing downward, and mark the location of

the two pilot holes.

2Remove the cable-entry cover, and, using a 3.2 mm (

1/8 in.)

bit, drill the pilot holes approximately 10 mm (

3/8 in.) deep.

3Fill the pass-through hole with marine sealant so it covers the

cable completely and there is excess sealant around the hole

and the cable.

4Place the cable-entry cover over the hole and the cable, with

the opening pointing downward.

5Apply marine sealant to the included 12 mm M4 screws, and

attach the cable-entry cover to the transom.

6Wipe away all excess marine sealant.

Testing the Installation

NOTICE

You should check your boat for leaks before you leave it in the

water for an extended period of time.

Because water is necessary to carry the sonar signal, the

transducer must be in the water to work properly. You cannot

get a depth or distance reading when out of the water. When

you place your boat in the water, check for leaks around any

screw holes that were added below the water line.

Testing the Transom-Mount Transducer Installation

NOTICE

When adjusting the depth of the transducer, make the

adjustments in small increments. Placing the transducer too

deep can adversely affect the performance of the boat and put

the transducer at risk of striking underwater objects.

Test the transom-mount transducer installation in open water

free of obstacles. Pay attention to your surroundings as you test

the transducer.

1With the boat in the water, turn on the chartplotter.

2Drive the boat at a slow speed. If the chartplotter appears to

be working properly, gradually increase speed while

observing the chartplotter.

3If the sonar signal is suddenly lost or the bottom return is

severely degraded, note the speed at which this occurs.

4Return the boat to the speed at which the signal was lost,

and make moderate turns in both directions while observing

the chartplotter.

5If the signal strength improves while turning, adjust the

transducer so that it extends another

1/8 in. (3 mm) below the

transom of the boat.

6Repeat steps 2–4 until the degradation is eliminated.

7If the signal does not improve, move the transducer to a

different location on the transom, and repeat the test.

Installing the Transducer on a Trolling Motor

Assembling the Trolling Motor Mount

1 Using the 8 mm M4 screws and 4 mm star washers ,

attach the trolling motor mount to the transducer .

2 Route the cable through the cable exit so the cable is on

the top side of the trolling motor housing when stowed.

Installing the Transducer on a Trolling Motor

NOTICE

Do not cut the transducer cable. Cutting the transducer cable

will void your warranty.

1 Insert a hose clamp (not included) through the slot on the

transducer mount , until equal lengths extend on both sides

of the mount.

2Place the transducer mount against the body of the trolling

motor with the narrow end of the transducer pointed away

from the propeller.

3Secure the hose clamp around the body of the trolling motor,

and tighten the hose clamp.

4Position the transducer so it is parallel to the bottom when in

use.

5Use cable ties (not included) to secure the transducer cable.

6Route the transducer cable to the installation location of the

sounder while taking these precautions.

• The cable should not be routed close to electrical wires or

other sources of electrical interference.

• The cable must not be pinched when the trolling motor is

deployed or stowed.

Specifications

Dimensions (L x W x

197.93 x 38.21 x 23.14 mm (7.8 x 1.5 x 0.9 in.)

Operating

temperature range

From 0° to 50°C (from 32° to 122°F)

Storage temperature

range

From -40° to 70°C (from -40° to 158°F)

Transmit power

(RMS)

500 W

Frequencies GT30: Garmin ClearVü: CHIRP 455 and

800 kHz

GT30: SideVü: CHIRP 455 and 800 kHz

GT34UHD: Garmin ClearVü: CHIRP 820 kHz

GT34UHD: SideVü: CHIRP 1.12 MHz

Maximum depth/

range1GT30: Garmin ClearVü™: 229 m (750 ft.)

GT30: SideVü: 76 m (250 ft.) each side, 152 m

(500 ft.) total

GT34UHD: Garmin ClearVü: 61 m (200 ft.)

GT34UHD: SideVü: 38 m (125 ft.) each side,

76 m (250 ft.) total

Garmin®

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,

registered in the USA and other countries. These trademarks may not be used without

the express permission of Garmin.

1 Dependent upon water salinity, bottom type, and other water conditions.

Product specificaties

Merk:	Garmin
Categorie:	Niet gecategoriseerd
Model:	GT34UHD-TM

Heb je hulp nodig?

Als je hulp nodig hebt met Garmin GT34UHD-TM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Garmin

Garmin Delta SE Handleiding

9 Juli 2023

Garmin Foretrex 801 Handleiding

8 Juli 2023

Garmin BMW Motorrad Navigator VI Handleiding

19 Juni 2023

Garmin GSD 26 Handleiding

18 Juni 2023

Garmin Dash Cam 54 Handleiding

15 Juni 2023

Garmin Varia ERTL615 Handleiding

6 Juni 2023

Garmin echoMAP CHIRP 72dv Handleiding

31 Mei 2023

Garmin STRIKER 7sv Handleiding

27 Mei 2023

Garmin GPSMAP 923xsv Handleiding

26 Mei 2023

Garmin GPSMAP 8400 Handleiding

25 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024