GARDE 181BASE1PSMA Handleiding

Bekijk gratis de handleiding van GARDE 181BASE1PSMA (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 20 mensen en kreeg gemiddeld 4.0 sterren uit 6 reviews. Heb je een vraag over GARDE 181BASE1PSMA of wil je andere gebruikers van dit product iets vragen? Stel een vraag

08/2023

IT IS RECOMMENDED THE KNIFE AND GEAR ARE

REPLACED AT THE SAME TIME FOR OPTIMAL PERFORMANCE.

1. Insert the can opener into the base. The base will be

needed for leverage while removing the gear.

2. Use a at head screwdriver to hold the gear in place by

jamming the head of the screw driver into the teeth of the

old gear. You will need to apply enough pressure to hold

the gear in place.

3. With the screwdriver in place, begin turning the handle

counter clockwise. You should feel the tension in the

spring ease up and the gear will come loose after a few

turns.

4. Remove the old gear and keep the washer. Insert the

new gear with the washer on top. Turn the handle clock-

wise until the handle connects to the shaft below the gear.

The spring should be tense now and the can opener is

ready to use.

(181CO1GEARMA)

REPLACING THE GEAR

1. Using either a Phillips or at head screw driver to remove

the 2 screws that connect the knife to the opener.

2. Remove and discard the old knife while keeping the

knife support plate.

3. Position the new knife in line with the holes and place the

support plate on top of the knife.

4. Use the screwdriver to tighten the screws.

(181CO1KNIFMA)

REPLACING THE KNIFE

The can opener’s surface should be cleaned regularly using

a food safe sanitizer.

Recommendation:

Noble Chemical’s QuikSan Sanitizer and Disinfectant (147QUIKSAN)

Use a toothbrush-style brush to ensure you are able to reach

the crevices around the knife.

Recommendation:

Scrubble Products 7¼ Utility Brush Stainless Steel Bristles (27140675)

After cleaning, apply a food safe oil to the gear to keep it

turning smoothly.

Recommendation:

Petrol-Gel Food Grade Sanitary Lubricant - 4 oz. Tube (401PETROGEL)

CLEANING / MAINTENANCE

USE CAUTION WHEN CLEANING

ITEM NUMBERDESCRIPTION

181BASE1PSMAPlated Steel Base

181COM1KITMAKnife & Gear Kit

181CO1GEARMAGear

181BASE1SSMAStainless Steel Base

181COM1SUPMAKnife Support

181CO1WASHMAWasher

181CO1KNIFMAKnife

181CO1SCRWMAScrew Set

These parts can be purchased from the same location as the can opener.

REPLACEMENT PARTS

1. Position the can you are opening on the counter on top of

the base with the lip of the can touching the can opener.

2. Line up the knife on the inside lip of the can. With the

handle upright, punch down so the knife punctures the

can’s lid.

3. Push the handle down so it is parallel with the counter

and begin turning the handle to open the can.

4. Once the lid is separated, safely remove it from the can.

Avoid touching the sharp edges of the lid created while

opening the can.

5. Pull the can opener up and move the can away from the

opener.

USING YOUR NEW CAN OPENER

The Garde Heavy-Duty #10 Can Opener is made of durable

cast iron construction with a rust-resistant coating. It can be

used to open cans of all sizes, including #10 cans.

ABOUT

Please read and comply with the instructions listed on this document. To get the

best service life and performance from your machine, clean it thoroughly before

and after each use by following the instructions listed below. Minimize the use of

alkaline cleaners as they may dull the nish and cause pitting.

181COM1BSSMA - Stainless Steel Base

181COM1BSTMA - Plated Steel Base

181COM1NBMA - No Base

MODELS

HEAVY DUTY #10 CAN OPENERS

QUICK START GU

Product specificaties