Futaba SBD-2 Handleiding

Bekijk gratis de handleiding van Futaba SBD-2 (2 pagina’s), behorend tot de categorie Radiografisch bestuurbaar speelgoed. Deze gids werd als nuttig beoordeeld door 38 mensen en kreeg gemiddeld 4.9 sterren uit 3 reviews. Heb je een vraag over Futaba SBD-2 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

S.BUS Decoder

SBD-2

Connection

Channel selection

*You should use an EXT battery, when using

many servos.

*If S.BUS/S.BUS2 servo

is connected to SBD-2,

CH written in S.BUS/

S.BUS2 servo will

ignore. S.BUS/S.BUS2

servo is operated by

CH of SBD-2.

Mini screwdriver used

* #0 of rotary switch

position does not

use it.

* DG1,DG2 : Switch channel output

connector

Conventional servos（other than S.BUS servo）

●Eight servos are connectable.

●SBD-2 can change the output

CH by rotary switch.

External battery

(For servos)

Ext battery switch

Connect the shorting pins

supplied when power is shared

with the receiver power source.

SBD-2

S.BUS / S.BUS2

Receiver

To S.BUS / S.BUS2

port

Rotary switch position

1 2 3 4 5 6 7 8 9

1CH1 CH9 CH8 CH4 CH9 CH9 CH8 CH4 CH1

2CH2 CH10 CH9CH5 CH10CH10 CH9CH5CH2

3CH3 CH11CH10 CH6 CH11CH11CH10 CH6CH3

4CH4 CH12CH11 CH7 CH12CH12CH11 CH7CH4

5CH5 CH13CH12 CH8 CH13CH13CH12 CH8CH5

6CH6 CH14CH13 CH9 CH14CH14CH13 CH9CH6

7CH7CH15 CH14 CH10 CH15DG1DG1DG1DG1

8CH8CH16 CH15 CH11DG1DG2DG2DG2DG2

Servo output connectors

SBD-2 LED state

OFF OFF

ON

S.BUS receive

error Blink

S. BUS

reception ON

Always use in the state in which the SBD-2 is

firmly attached to the fuselage of the airplane or

helicopter.

■ There is the danger of loss of control and crashing

if the connector is disconnected by vibration and

shock.

When using analog servos, always use in the state

in which the receiver is normal mode.

■ There is the danger of erroneous operation or

damage on the FASST12ch / High-speed mode.

Do not connect an S.BUS/S.BUS2 connector of the

SBD-2 to other than an S.BUS/S.BUS2 connection port.

■ There is the danger of erroneous operation or

damage.

Do not use the SBD-2 with anything other than an

R/C model.

To ensure that the SBD-2 is functioning as desired,

please test accordingly.

■ Do not y until inspection is complete.

Do not connect shorting pins, when using an Ext

battery.

■ There is the danger of explosion and ignition.

Ensure that the unit is mounted in an area that will

eliminate exposure to fuel, water and vibration.

■As with any electronic components, proper

precautions are urged to prolong the life and

increase the performance of the SBD-2.

Allow a slight amount of slack in the SBD-2 cables

and fasten them Eat a suitable location to prevent

any damage from vibration during ight.

Do not connect either

a switch or battery in

this manner.

■When a connector

is inserted like the

left, it short-circuits

and there is danger

of explosion and

ignition.

WARNNG

INSTRUCTION MANUAL

Before using your new SBD-2, please read this manual

thoroughly and use the system properly and safely.

After reading this manual, store it in a safe place.

Thank you for purchasing an SBD-2, S.BUS decoder. The

SBD-2is a converter for using conventional servos (other

than S.BUS servo) with the S.BUS/S.BUS2

system. The

SBD-2 connects to the receiver output of a S.BUS/S.BUS2

system and eight servos can be used.

SBD-2can change the output CH from 9 groups select by

rotary switch. SBD-2 can use EXT battery (for servos).

Applicable receiver: S.BUS/S.BUS2

system receiver only

Usage Precautions

Connections and Name of Each Part of the SBD-2

Futaba Corp. will not be responsible for damage

caused by combination with other than Futaba

Genuine parts.

Input connector

●C o n n e c t s t ot h eS .B U S /

S.BUS2 port of the receiver.

Rotary switch

Servo output connectors (1~8)

●Connecttheservos.

External battery

connector

(EXT.BATT)

●Connect the shorting pins

supplied when power is

shared with the receiver

power source.

Mini screwdriver

Monitor LED

©Copyright 2014. No part of this manual may be reproduced in any form without prior permission. The contents of this

manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent

errors or omissions. Please contact our service center if you feel that any corrections or clarifications should be made.

FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan

©FUTABA CORPORATION 2014, 8 (1)

[SBD-2 Ratings]

• Dimensions:

29.6mm x 39.3mm x 15.8mm

(1.17in.x 1.55in. x 0.62in.)

(excluding protruding)

• Weight:

14.2g (0.5 oz.)

• Power requirement:

4.8V～7.4V

Monitor LED

OK

Product specificaties