Forte Lighting 2743-06 Handleiding
Pagina's 1 Lamp
Bekijk de handleiding van Forte Lighting 2743-06 gratis online of download de PDF. 32 mensen vonden deze handleiding nuttig. Vraag over dit model? Stel een vraag
2743-03 2743-06
Connect the lamp holder (N) to the lamp holder (P) and lock it
with (T). Secure shade (Q) onto the socket (O) by screwing
socket ring (R) tightly. Install light bulb (not included) in
accordance with the fixture’s specifications. Do not exceed
the recommended maximum wattage.
Carefully remove all contents from the carton. See the
important notes above. Shut off the power at the circuit
breaker and completely remove the old fixture from the
ceiling, including the old crossbar. Remove the crossbar
assembly from the bag. Crossbar (B) contains several
pairs of threaded holes. Find the pair of holes that matches
the spacing of the holes on the junction box and the fixture’s
canopy. Two mounting screws (A) should be attached to
crossbar (B). You may need to tighten nuts (C) to hold these
screws in place. Pull the house wires through the center of
crossbar (B). Place crossbar (B) over the junction box so
that mounting screws (A) are vertical and aligned with
the hole locations on the fixture’s canopy (F). Secure
crossbar (B) to the junction box by tightening the screws.
crossbar
crossbar
There are an 18 inch rod (K), a 12 inch rod (L), and a 6
inch rod (M) included for each fixture. Rod (L) is wired.
Determine the correct number of rods needed for proper
hanging height. To lengthen the fixture, add additional rods.
If additional rods are needed, contact the place of purchase
to order. To shorten the fixture, trim the wires to the desired
length, leave at least 8 to 10 inches of wire in addition to the
desired length and slide any excess rods off to discard. Keep
in mind that you must use at least the provided 6 inch rod (M)
Push canopy (F) up to the ceiling and tighten the deco nuts (H)
onto the exposed mounting screws (A).
to hang the fixture. Thread the wires through the rods and
pull the wires until taut before connecting the rods together.
Thread bottom rod (M) onto nipple (N) on the fixture. Thread
the nipple of the top rod onto swivel post (I) of canopy (F).
Pull the fixture wires through the top of the canopy.
SMOOTH
o
P
T
Product specificaties
| Merk: | Forte Lighting |
| Categorie: | Lamp |
| Model: | 2743-06 |
Heb je hulp nodig?
Als je hulp nodig hebt met Forte Lighting 2743-06 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Lamp Forte Lighting
Forte Lighting 7096-06 Handleiding Forte Lighting 7120-05 Handleiding Forte Lighting 2745-06 Handleiding Forte Lighting 2748-05 Handleiding Forte Lighting 2743-03 Handleiding Forte Lighting 2748-09 Handleiding Forte Lighting 7100-04 Handleiding Forte Lighting 7114-05 Handleiding
Alle Forte Lighting Lamp handleidingen
Populair in Lamp
Forte Lighting 2651-01 Handleiding Forte Lighting 7108-01 Handleiding Forte Lighting 2678-01 Handleiding
Handleiding Lamp
Nieuwste handleidingen voor Lamp
EMOS REXXO ZB2220 Handleiding Osram Decor Spot Jupiter 4 Handleiding Triton Blue Horizon 30 Black Handleiding Dainolite PAG-231P Handleiding Dainolite URI-101P Handleiding EMOS TAMBO Evo ZS2534 Handleiding Dainolite FCA-920LEDP Handleiding Gamma Florida Handleiding Dainolite WNR-1415LEDW Handleiding EMOS TAMBO Evo ZS2554 Handleiding