Flyzone Sensei FS Handleiding

Flyzone Radiografisch bestuurbaar speelgoed Sensei FS

Lees hieronder de 📖 handleiding in het Nederlandse voor Flyzone Sensei FS (20 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/20

SPECIFICATIONS

Wingspan: 58 in

[1475mm]

Wing

Area:

566 in2

[36.5 dm2]

Weight: 3.25 lb

[1470 g]

Wing

Loading:

13 oz/ft2

[40 g/dm2]

Length: 48 in

[1220 mm]

Radio: 6-channel

(required)

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

WARRANTY

Hobbico guarantees this kit to be free from defects in both

material and workmanship at the date of purchase. This warranty

does not cover any component parts damaged by use or

modification. In no case shall Hobbico’s liability exceed the

original cost of the purchased kit. Further, Hobbico reserves

the right to change or modify this warranty without notice.

In that Hobbico has no control over the final assembly or material

used for final assembly, no liability shall be assumed nor

accepted for any damage resulting from the use by the user of

the final user-assembled product. By the act of using the

user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated

with the use of this product, the buyer is advised to return

this kit immediately in new and unused condition to the

place of purchase.

To make a warranty claim send the defective part or item to

Hobby Services at the address below:

Hobby Services

3002 N. Apollo Dr. Suite 1

Champaign IL 61822 USA

Include a letter stating your name, return shipping address, as

much contact information as possible (daytime telephone

number, fax number, e-mail address), a detailed description of

the problem and a photocopy of the purchase receipt. Upon

receipt of the package the problem will be evaluated as quickly

as possible.

I N S T R U C T I O N M A N U A L

™

PECIFICATION

ngspan

[

1475mm

]

ea:

566

[

36.5 d

]

[

1470

Wing

Load

[40 g/d

]

engt

[

]

Radio:

-channel

™

INTRODUCTION

Thank you for purchasing the Flyzone Sensei. The best method

to learn to ﬂ y an R/C plane is with a stable trainer. This upgraded

version of the Sensei includes a gyro stabilization system that

will aid the beginning pilot in learning to ﬂ y with an instructor

and by themselves. With three modes to choose from, the

amount of ﬂ ight assistance the stabilization adds is adjustable

to match your improving ﬂ ying skills. To make it even easier,

the Sensei is electric. Just charge the batteries and you’re

ready ﬂ y. When you’re done, just put the plane away until the

next time. Assembly is quick and easy. In the RTF version,

nothing else is needed to get you in the air.

For the latest technical updates or manual corrections to

the Sensei visit the Hobbico web site at www.hobbico.

com. Open the “Airplanes” link, then select “Sensei”. If

there is new technical information or changes to this model

a “tech notice” box will appear in the upper left corner of

the page.

AMA

If you are not already a member of the AMA, please join! The

AMA is the governing body of model aviation and membership

provides liability insurance coverage, protects modelers’ rights

and interests and is required to ﬂ y at most R/C sites.

Academy of Model Aeronautics

5151 East Memorial Drive

Muncie, IN 47302-9252

Ph. (800) 435-9262

Fax (765) 741-0057

Or via the Internet at: http://www.modelaircraft.org

IMPORTANT!!! Two of the most important things you can

do to preserve the radio controlled aircraft hobby are to avoid

ﬂ ying near full-scale aircraft and avoid ﬂ ying near or over

groups of people.

SAFETY PRECAUTIONS

Protect Your Model, Yourself & Others…

Follow These Important Safety Precautions

Your Sensei should not be considered a toy, but rather a

sophisticated, working model that functions very much like a

full-size airplane. Because of its performance capabilities, the

Sensei, if not assembled and operated correctly, could possibly

cause injury to yourself or spectators and damage to property

2. You must assemble the model according to the

instructions. Do not alter or modify the model, as doing

so may result in an unsafe or unﬂ yable model. In a few

cases the instructions may differ slightly from the photos. In

those instances the written instructions should be considered

as correct.

3. If you are not an experienced pilot or have not ﬂ own an

R/C plane before, we recommend that you get the assistance

of an experienced pilot in your R/C club for your ﬁ rst ﬂ ights.

If you’re not a member of a club, your local hobby shop has

information about clubs in your area whose membership

includes experienced pilots.

We, as the kit manufacturer, provide you with a top quality,

thoroughly tested kit and instructions, but ultimately the

quality and ﬂ yability of your ﬁ nished model depends

on how you build it; therefore, we cannot in any way

guarantee the performance of your completed model, and

no representations are expressed or implied as to the

performance or safety of your completed model.

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

AMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . .2

ADDITIONAL ITEMS REQUIRED. . . . . . . . . . . . . . . . . . .3

Radio Control System . . . . . . . . . . . . . . . . . . . . . . . . .3

Battery and Charger. . . . . . . . . . . . . . . . . . . . . . . . . . .3

Assembly Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BATTERY PREPARATIONS . . . . . . . . . . . . . . . . . . . . . . .3

Charge the Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Battery Charging Precautions . . . . . . . . . . . . . . . . . . .3

Battery Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Install the Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . .3

ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . .4

ASSEMBLE THE SENSEI . . . . . . . . . . . . . . . . . . . . . . . . .5

Install the Main Landing Gear . . . . . . . . . . . . . . . . . . .5

Install the Vertical and Horizontal Stabilizer . . . . . . . . .5

Connect the Rudder and Elevator Controls . . . . . . . . .6

Install the Wing Joiner . . . . . . . . . . . . . . . . . . . . . . . . .7

RX-R VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Install the Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . .8

TTX650 Programming . . . . . . . . . . . . . . . . . . . . . . . . .8

RADIO SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Check the Radio System . . . . . . . . . . . . . . . . . . . . . . .9

Check the Control Throws . . . . . . . . . . . . . . . . . . . . .11

Check the Stabilization System . . . . . . . . . . . . . . . . .12

Mount the Propeller . . . . . . . . . . . . . . . . . . . . . . . . . .13

Check the C.G. (Center of Gravity) . . . . . . . . . . . . . .13

Important ESC Information . . . . . . . . . . . . . . . . . . . .14

WISE GYRO STABILIZATION SYSTEM. . . . . . . . . . . . .15

Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Recovery Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Climb Assist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

COWL REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

GET THE MODEL READY TO FLY. . . . . . . . . . . . . . . . .17

FLYING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Takeoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Flight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Landing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Before Your Next Flight. . . . . . . . . . . . . . . . . . . . . . . .19

Improving Your Piloting Skills . . . . . . . . . . . . . . . . . . .20

Trimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

TABLE OF CONTENTS

ADDITIONAL ITEMS REQUIRED

Radio Control System

The Sensei Rx-R (Receiver Ready)

comes with the servos installed, so

all that is required is a 6-channel

transmitter and receiver. The Tactic™

TTX610 2.4GHz spread spectrum

6-channel radio control system

(TACJ2610) is included with the RTF

(Ready to Fly) version of the Sensei,

so this same radio system is ideal for

your Rx-R version, too.

❏

Tactic TTX610 2.4GHz 6-channel system (TACJ2610)

❏

(4) AA batteries will be required to operate the

recommended transmitter (FUGP7308).

Battery and Charger

The Sensei RTF comes complete with a motor battery and

charger. The Sensei Rx-R version requires a 2200mAh 11.1V

LiPo battery and LiPo Charger. The Sensei was designed for

the Flyzone 2100mAh 11.1V LiPo battery (FLZA6173). Other

LiPo batteries similar in size and connector may also work.

A LiPo battery charger is also required. A safe economical

charger is the Great Planes 3S (3-cell/ 11.1V) LiPo AC/DC

Smart Charger (GPMM3318).

Assembly Tools

Other than common hobby tools this is the list of building

supplies that are required to ﬁ nish the Sensei.

❏

Small needle-nose pliers (HCAR0625)

or hemostats (SQUR2502)

❏

#1 Phillips screwdriver (DTXR0174)

❏

Small crescent wrench

❏

Great Planes stick-on lead weight

(Optional, GPMQ4485)

BATTERY PREPARATION

Before starting to assemble the Sensei, we recommend

charging the motor battery. Then, when you are ready to set

up the radio system, the motor battery can be used to power

the receiver.

Charge the Battery

The following is an overview of how to charge your motor

battery using the ElectriFly Smart Charger. If you are using a

different LiPo charger, carefully follow the instructions included

with the charger.

1. Connect the input power to the charger. The GREEN LED

will be lit, indicating standby mode. The RED LED will be OFF.

2. Connect the battery to be charged to the balance plug.

The RED LED will also be lit, and remain RED during the

charging. Both LEDs should be lit solid while charging.

3. If the battery was completely discharged, the RED and

GREEN LEDs will start to ﬂ ash after 2-hours and 40-minutes.

The charger has a built in safety timer.

4. Disconnect the battery from the charger, wait for the GREEN

LED to be lit, and then reconnect the battery to the charger.

5. It will take approximately 1-1/2 hours more to complete the

charge. When the battery is fully charged, the GREEN LED

will turn OFF. Remove the battery from the charger at this time.

6. Charging time depends on the level of discharge of the

battery and if the battery cells were unbalanced.

LED SCHEME Use this table to determine charge action.

RED LED

OFF

Solid ON

Flashing

GREEN LED

Solid ON

Flashing

Solid ON

OFF

Flashing

ACTION

No battery is connected

Conditioning battery

Battery charging

Charge complete

ERROR*

*Possible sources of battery error may include a highly unbalanced

pack, charger timed out, or one cell of the pack which is low voltage. In

the case of a battery error, please remove the battery pack from the

charger and inspect it carefully for swelling or any other damage, such

as broken wires.

Battery Charging Precautions

● Be careful to avoid overcharging the battery. Only use a LiPo

approved charger. Never use a NiCd/NiMH peak charger.

● Remember to check the temperature of the battery during

the charge. The battery should not get hot. If it does, unplug

the battery from the charger.

● Charge the battery at a maximum charge rate of 2.1 amps.

A higher charge rate will cause the battery to get hot.

● Never place the battery on combustible material or leave it

unattended while charging.

● Never charge the battery in the plane.

● We recommend that a balancing charger be used to charge

the battery. A properly cared for battery will last a long time. If

the battery pack is continually charged without balancing the

individual cells, the life of the battery pack will be shortened.

Battery Recycling

Attention: The Sensei is powered by a rechargeable battery.

At the end of the battery’s useful life, under various state and

local laws, it may be illegal to dispose of the battery into the

municipal waste system. Check with your local solid waste

ofﬁ cials for details in your area for recycling options or proper

disposal. We encourage contacting your local recycling center

for more information.

Product specificaties

Merk:	Flyzone
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	Sensei FS
Kleur van het product:	Grey, Red, White
Gewicht:	1450 g
Materiaal behuizing:	Schuim
Oplader:	Ja
Lengte:	1220 mm
Constructietype:	Montagekit
Aantal kanalen:	4 kanalen
Type motor:	Borstelloos
Spanwijdte:	1475 mm
Elektronische toerentalregeling (ESC):	Ja
Vleugeloppervlak:	3650 cm²
Aanbevolen batterij:	3S 11.1V 1800-2200mAh 30C LiPo