Fluke 700HTP-2 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke 700HTP-2 (2 pagina's) in de categorie Pomp. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
PN 4096896
September 2011
2011 Fluke Corporation. All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies.
How to Prime Pump the Test
Before you connect the to the Unit Under T), the Pump Test (UU
Pump must be lled with uid and primed for use. Follow the
directions below to prepare the for use. Pump
1. Fill the with uid: Pump
a. Remove the Reservoir Filler Cap (item .)
b. Fill the Hydraulic Fluid Reservoir approximately -thirds full two
(66 with distilled water, mineral oil, or hydraulic oil. cc)
Note
If water is used in the , use only DISTILLED water Pump
and drain the water out of the after use. Pump
c. Install the Reservoir Filler Cap (item .) Tighten by hand.
2. the : Prime Pump
a. Adjust the Vernier Fine Adjustment Knob (item ) to the
approximate dle-range.mid
b. Turn the Pressure Bleed Knob (item ) clockwise until it
stops in the full closed position.
c. Squeeze the handles together to pump uid. uid until Pump
uid shows at the . Pump Port
d. Attach the uid hose to the . Pump
e. Squeeze the handles together until uid shows at the end of
the hose.
f. Attach the uid hose to the Unit Under (UUT) and Test
squeeze the handles until pressure increases. Pump
g. Bleed the trapped air from the Pump. Pressurize the Pump to
1,000 psi then slowly turn the Pressure Bleed Knob (item )
counter-clockwise to release pressure.
Notes
• As the pressure it will be hard to squeeze the rises
handles together. Use the Handle Limiter (item ) to
limit the travel of the handles which will make them
easier to squeeze together. toggle the Handle To
Limiter on or o, squeeze the handles together and
push the Handle Limiter (item
) in or out.
• The rate at which the pressure increases is directly
related to the test conguration (hose length and
volume of UUT.)
Replacement Parts
Rebuild Kit, Fluke PN 4097836
Hydraulic Fluid Reservoir Rebuild , Fluke PN 2844341 Kit
Handle Assembly Rebuild , Fluke PN 2844352 Kit
LIMITED WARRANTY AND OF LIABILITYLIMITATION
This Fluke product will be from defects in material and workmanship for free
one year from the date of purchase. This warranty does not cover fuses,
disposable batteries, or damage from accident, neglect, misuse, alteration,
contamination, or conditions of operation or . Resellers are abnormal handling
not authorized any obtain to extend other warranty on Fluke’s behalf. To
service during the warranty period, contact your nearest Fluke authorized
service r cente to obtain return authorization information, then send the product
to that with a description of the problem.Service Center
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES,
SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR
IMPLIED. FLUKE SPECIAL, INDIRECT, IS NOT LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING
FROM ANY CAUSE OR THEORY. Since some states or countries do not
allow the exclusion or of an implied warranty or of incidental or limitation
consequential damag not apply to you.es, this limitation of liability may
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99
Fluke 700HTP- -2
Hydraulic Test Pump
Instruction Sheet
Introduction
The Fluke 700HTP-2 Hydraulic (the or ProductTest Pump Pump ) is a
portable source of high pressure.
Safety
W Warning
To prevent personal injury se the Product only as , u
specified, or the protection supplied by the Product can be
compromised.
Pump Sp ecifications
• Maximum pressure: 10,000 psi (690 bar)
• raulic media: distilled water, mineral based hydraulic oil, up Hyd or
to hydraulic oil 100 (30 W).
• Wetted materials: 303 stainless steel, aluminum, polyurethane,
PTFE, nitrile, and nylon.
• Weight: 1.29 lb (0.58 kg)
• Dimensions: length 9.5 41 mm), width 6.1 in (155 mm), depth in (2
2.6 in (66 mm)
Box Contents
• Model 700HTP-2 Hydraulic with a 1/4- NPT tee Test Pump inch
installed.
• 1/4- NPT male to 1/4- female adapters. Two inch inch BSP
• One 1/4- NPT male to 1/4- NPT male tting. inch inch
• One 1/4- NPT male to 1/8- NPT male tting. inch inch
• Instruction Sheet
How to Contact Fluke
To contact Fluke, call one of the following telephone numbers:
• Technical Support USA: 1-800-44-FLUKE
(1-800-443-5853)
• Calibration/Repair USA: 1-888-99-FLUKE
(1-888-993-5853)
• Canada: 1-800-36-FLUKE
(1-800-363-5853)
• Europe: +31 402-675-200
• Japan: +81-3-6714-3114
• Singapore: +65-738-5655
• Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.fluke.com.
To register your product, visit . http://register.uke.com
To view, print, or download the latest manual supplement, visit
http://us.uke.com/usen/support/manuals.
Features
gsp001.eps
No. Item Function
Master
Instrument Port
Port for Fl uke 700 Series Pressure
Module, 1/4-inch NPT female.
Test Pressure
Port
Port for pressure instrument under
test, 1/4-inch NPT female.
Pressure Relief
Valve Port
Port for an optional Fluke 700PRV-1
Pressure Relief Valve (plugged).
Vernier Fine
Adjustment Knob
Lets you adjust the applied pressure
in small increments.
Hydraulic Fluid
Reservoir
Holds 100 cc of mineral based
hydraulic oil, distilled water, or
hydraulic oil.
1/4-inch NPT Tee
Fitting For master and test ports.
Handle Limiter Limits the travel of the handles.
Reservoir Filler
Cap
Cap which seals the hydraulic uid
reservoir. Install before you pump.
Pressure Bleed
Knob
Lets you release pressure in small
increments.
Reservoir Nut Remove nut to clean reservoir.
gsp002.eps
Figure 1. Test Configuration
How to Operate the Test Pump
W Warning
To prevent a violent release of pressure, open the
Pressure ) very slowlyBleed Knob (item before you
disconnect pressure lines. Do not connect the Pump to
an external pressure source.
W Caution
To prevent damage hen odule or w a Pressure M Pressure
I nstrument is connected that could be damaged by
pressures of 690 bar (10,000 psi), install and correctly
set a relief valve in the system or an optional Fluke
700PRV-1 Pressure Relief Valve on the . Pump
1. Connect a 700 Series Pressure Module (the Pressure Module)
to the Master Instrument (item .) To connect to a 700P Port
High Pressure Module (700P29, P30, or P31) install a male
1/4-inch NPT Adapter. Use Teon
® tape or equivalent on the
NPT thread connections to prevent leaks.
2. Fill and the . See “How to the Prime Pump Prime Test Pump”.
3. Connect the Pressure Module to the calibrator as shown in
Figure 1.
4. Connect the input of the Pressure Unit Under Test U to the (U T)
Test Port Test Pressure (item ) on the . Pump
5. Loosen the Pressure Bleed Knob (item ) to release pressure
from the . Pump
6. Use the Calibrator to z the Pressure Module. Refer to the ero
Users Manual for instructions.
7. Turn the Adjustment Knob (item ) to the Vernier Fine
middle-range.
8. Turn the Pressure Bleed Knob (item ) clockwise until it stops
in the full closed position.
9. Squeeze the handles together to pump increase fluid which will
pressure. See the Notes in step 2 of the “How to the Prime Test
Pump” procedure.
W Caution
To prevent damage, do not let the pressure increase to
more than the pressure rating of the equipment under
test. Pressure can increase quickly if the pressurized
volume is small.
10. incremental pressure adjustments, use the Vernier Fine For
Adjustment Knob.
11. Once the test is done, slowly turn the Pressure Bleed Knob
(item ) counter-clockwise to release pressure.
Product specificaties
| Merk: | Fluke |
| Categorie: | Pomp |
| Model: | 700HTP-2 |
Heb je hulp nodig?
Als je hulp nodig hebt met Fluke 700HTP-2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Pomp Fluke
26 Juli 2023
13 Juni 2023
3 Maart 2023
1 Maart 2023
23 Februari 2023
12 Februari 2023
15 November 2022
Handleiding Pomp
- Pomp Karcher
- Pomp Nefit
- Pomp Quigg
- Pomp Siemens
- Pomp Vaillant
- Pomp Al-ko
- Pomp Astralpool
- Pomp Bartscher
- Pomp Batavia
- Pomp Bestway
- Pomp Blumfeldt
- Pomp Bulex
- Pomp Danfoss
- Pomp Eheim
- Pomp Einhell
- Pomp Eufab
- Pomp Eurom
- Pomp Ferroli
- Pomp Fuxtec
- Pomp Gardena
- Pomp Generac
- Pomp Germania
- Pomp GRE
- Pomp Gude
- Pomp Hayward
- Pomp Hozelock
- Pomp Husqvarna
- Pomp Hyundai
- Pomp Lavorwash
- Pomp Makita
- Pomp Melinera
- Pomp Metabo
- Pomp Michelin
- Pomp Milwaukee
- Pomp Nibe
- Pomp Parkside
- Pomp Plantiflor
- Pomp POLARIS
- Pomp Powerfix
- Pomp Powerplus
- Pomp Ryobi
- Pomp Sanibroyeur
- Pomp Scheppach
- Pomp Silvercrest
- Pomp Toolcraft
- Pomp Trotec
- Pomp Ultimate Speed
- Pomp Velda
- Pomp Vetus
- Pomp Vonroc
- Pomp Westfalia
- Pomp WHALE
- Pomp Zipper
- Pomp Zodiac
- Pomp Oase
- Pomp OKAY
- Pomp Osram
- Pomp Ozito
- Pomp Crivit
- Pomp Black And Decker
- Pomp Wetelux
- Pomp Cannondale
- Pomp Sicce
- Pomp Simpson
- Pomp Tacklife
- Pomp Fieldmann
- Pomp Lezyne
- Pomp Topeak
- Pomp Zéfal
- Pomp Coleman
- Pomp Outwell
- Pomp Biltema
- Pomp Sun Joe
- Pomp Little Giant
- Pomp ESPA
- Pomp Verto
- Pomp Enermax
- Pomp FIAP
- Pomp Neptun
- Pomp Pontec
- Pomp Alpha Tools
- Pomp Jabsco
- Pomp SKS
- Pomp For_Q
- Pomp Waldbeck
- Pomp Pedrollo
- Pomp Park Tool
- Pomp Panduit
- Pomp DAB
- Pomp Ubbink
- Pomp Esotec
- Pomp Wayne
- Pomp T.I.P.
- Pomp Rule
- Pomp JANDY
- Pomp Elpumps
- Pomp Hollex
- Pomp B-Air
- Pomp Baracuda
- Pomp Lifan
- Pomp Monzana
- Pomp Liberty Pumps
- Pomp BluGarda
- Pomp Grundfos
- Pomp Madimack
- Pomp Sauermann
- Pomp Eco-Flo
- Pomp Nowax
- Pomp Zoeller
- Pomp Superior Pump
- Pomp SHURflo
- Pomp EvoHeat
- Pomp Barwig
- Pomp Ebara
- Pomp Basement Watchdog
- Pomp Ergotools Pattfield
- Pomp Zehnder Pumpen
- Pomp SANDPIPER
Nieuwste handleidingen voor Pomp
18 April 2024
18 April 2024
16 April 2024
16 April 2024
3 April 2024
28 Maart 2024
21 Maart 2024
21 Maart 2024
21 Maart 2024
21 Maart 2024