Fischer FZA 10 x 40 M 6/10 Handleiding

Bekijk gratis de handleiding van Fischer FZA 10 x 40 M 6/10 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 48 mensen en kreeg gemiddeld 4.9 sterren uit 7 reviews. Heb je een vraag over Fischer FZA 10 x 40 M 6/10 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

66

1

3

1

2

2

3

4

4

Installation Instructions fischer Zykon-Anchor

Push-through installation

FZA-D

Pre-positioned installation

FZA

FZA-I

Create a drill hole at right angles to the surface of the

anchor base with a hammer drill, using the correspond-

ing Zykon universal drill bit FZUB. The required drill

depth is reached once the FZUB depth stop meets the

concrete.

Clean drill hole;

blow out or clean with a vacuum cleaner.

Create a drill hole through the installation object at right

angles to the surface of the anchor base with a hammer

drill, using the corresponding Zykon universal drill bit

FZUB. The required drill depth is reached once the FZUB

depth stop meets the concrete.

Once the FZUB depth stop meets the concrete, create

the drill hole undercut by making circular swivelling

movements with the hammer drill while the ham-

mer mechanism is engaged. Press the hammer drill

firmly against the fixture; 1–2 swivelling movements

is sufficient for

∅

14 mm, with 3–5 movements for

∅

18 mm and

∅

22 mm.

Once the FZUB depth stop meets the concrete, create

the drill hole undercut by making circular swivelling

movements with the hammer drill while the hammer

mechanism is engaged. Press the hammer drill firmly

against the anchor base; 1–2 swivelling movements

is sufficient for

∅

14 mm, with 3–5 movements for

∅

18 mm and

∅

22 mm.

Clean drill hole;

blow out or clean with a vacuum cleaner.

Insert the anchor into the drill hole and then drive the

expansion sleeve in with hammer-set device FZE Plus,

using a manual hammer. The anchor sleeve sits

min. 1 mm behind the surface of the attachment (see

picture 5).

Mount installation object (e.g. anchor plate), washer and

nut or screw (for FZA-I) and apply installation torque

with torque spanner.

Mount installation object (e.g. anchor plate), washer and

nut or screw (for FZA-I) and apply installation torque

with torque spanner.

The thickness of the fixture have to fullfill the terms of

the related approval.

FZA

FZA-D

FZA-I

ETA-98/0004, FZA,

FZA A4, FZA C

* Approval Z-21.1-1646 covers the following anchor types:

FZA: FZA 10 x 40 M 6, FZA 12 x 40 M 8, FZA 14 x 40 M 10 in galvanised steel and stainless steel A4.

FZA-I: FZA 12 x 40 M 6 I, FZA 14 x 60 M 8 I, FZA 18 x 80 M 10 I in galvanised steel and stainless steel A4.

The anchor is correctly expanded if the green colour on

the thread of the tapered bolt is visible.

The anchor is correctly expanded if the green colour on

the thread of the tapered bolt is visible (FZA) or the

gap u (FZA-I) (when installed acc. to table 8, annex 7)

is fulfilled.

Insert the anchor into the drill hole and then drive the

expansion sleeve in with hammer-set device FZE Plus,

using a manual hammer. The anchor sleeve sits min.

1 mm behind the surface of the concrete (see picture 5).

Installing the FZA-I with internal thread the centring pin

FZE-I should be used additionally.

The regulations of the building-authority approvals ETA-98/0004 and respectively Z-21.1-1646 have to be observed.

5

5

From thread M10

Shock-tested/

BZS approval for

shock-resilient

fixings in civil

defence areas.

Z-21.1-1646

For extraordinary actions e.g. in

nuclear power plants. See approval

for anchor types*.

Product specificaties