Ferm SGM1006 Handleiding
Ferm
Soldeermachine
SGM1006
Lees hieronder de 📖 handleiding in het Nederlandse voor Ferm SGM1006 (36 pagina's) in de categorie Soldeermachine. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/36
WWW.FERM.COM
SGM1006
SGM1006
SGM1006
SGM1006
Original instructions 03
Übersetzung der Originalbetriebsanleitung 04
Vertaling van de oorspronkelijke gebruiksaanwijzing
06
Traduction de la notice originale 07
Traducción del manual original 09
Tradução do manual original 10
Traduzione delle istruzioni originali 12
Översättning av bruksanvisning i original 13
Alkuperäisten ohjeiden käännös 15
Oversatt fra orginal veiledning 16
Oversættelse af den originale brugsanvisning 18
Eredeti használati utasítás fordítása 19
Překlad püvodního návodu k používání 21
Preklad pôvodného návodu na použitie 22
Tłumaczenie instrukcji oryginalnej 24
Originalios instrukcijos vertimas 25
Instrukciju tulkojums no oriģinālvalodas 27
Algupärase kasutusjuhendi tõlge 28
Μετάφραση του πρωτοτύπου των οδηγιών χρήσης 30
Копија на оригиналот инструкции 31
EN
DE
NL
FR
ES
PT
IT
SV
FI
NO
DA
HU
CS
SL
PL
LT
LV
ET
EL
MK
2
16
14
12
13
10
11
9
15
7
1
6
5
4
3
8
Fig. A
3
EN
MULTIPURPOSE GAS SOLDERING
TOOL
The numbers in the following text correspond
with the pictures at page 2
Features
1. Switch
3. Nut
4. Soldering head
5. Filling valve
6. Flow control knob
7. Ignition button
8. Guard
9. Standard tip
10. Diagonal tip (3 mm)
11. Chisel tip (3,5 mm)
12. Hot knife
13. Hot blower
14. Reflector
15. Wrench (7 mm)
16. Wrench (8 mm)
Warnings
• Do not fill gas or store near open flame, heater
or combustible materials
• Use only high quality butane gas
• Butane gas is highly flammable, please handle
with care
• Do not drop, puncture, or incinerate
• Do not store or operate in a place where the
temperature is above 50º C (122º F)
• Keep out of reach of children
• Cool down before putting protective cap on
and before storing
Gas filling and refilling
• Ensure the switch (1) is turned to the OFF
position before filling
• Reverse the unit; insert the gas container’s
nozzle vertically into filling valve (5)
• When gas escapes from filling valve, remove
the nozzle from the filling valve
Ignition
• Move the flow control knob (6) to the middle
position
• Move the switch (1) upward and to the right
• Press down the ignition button (7) to light up
the open flame
Shutting off
Move the switch (1) upwards and to the left. The
switch will return to OFF position.
Flame lengt or temperature adjustment
After ignition, turn the flow control knob (6) to the
right to increase the flame length of the torch or
the temperature of soldering tip or hot air, to the
left to decrease the flame length or the
temperature.
Operating tips
• After filling or refilling with gas, wait for
approximately 2 minutes so that the gas in the
cylinder can be stable.
• Soldering tips must be tin-plated before using
them for the first time. A thin layer of solder
should be applied to the tip when it has been
heated.
• Soldering should NOT be carried out on “live”
circuits, as this soldering unit does not
possess any special electrical insulation
• Keep your soldering sponge moist
How to fit or replace different
accessoires
Always allow unit to cool before removing
or replacing tips
Replace soldering tips
• With 7 mm wrench (15) on the soldering tip or
hot blow head (9 till 14) and 8 mm wrench on
the soldering head (4), you can tight the tip or
hot blow head or unscrew them.
• When you unscrew the nut (3), you can
remove the guard (8) and soldering head (4).
Now the unit becomes an open flame torch.
Troubleshooting
1. Does not ignite
• Empty gas
• Refill butane gas
• Gas pressure too high or too low
• Slide flow control knob (6) to lower or higher
position
Product specificaties
| Merk: | Ferm |
| Categorie: | Soldeermachine |
| Model: | SGM1006 |
| Gewicht: | 670 g |
| Soort: | Gassoldeerbout |
| Type verpakking: | Doos |
| Temperatuur (max): | 375 °C |
Heb je hulp nodig?
Als je hulp nodig hebt met Ferm SGM1006 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Soldeermachine Ferm
26 Mei 2023
Handleiding Soldeermachine
- Soldeermachine Basetech
- Soldeermachine Denon
- Soldeermachine Einhell
- Soldeermachine Gude
- Soldeermachine Gys
- Soldeermachine Holzmann
- Soldeermachine HQ
- Soldeermachine Maestro
- Soldeermachine Mercury
- Soldeermachine Milwaukee
- Soldeermachine Monacor
- Soldeermachine Nedis
- Soldeermachine Parkside
- Soldeermachine Powerfix
- Soldeermachine Powerplus
- Soldeermachine Ryobi
- Soldeermachine Sievert
- Soldeermachine Silverline
- Soldeermachine Telwin
- Soldeermachine Toolcraft
- Soldeermachine Trotec
- Soldeermachine Velleman
- Soldeermachine Weller
- Soldeermachine Westfalia
- Soldeermachine Ozito
- Soldeermachine Steren
- Soldeermachine Cocraft
- Soldeermachine Truper
- Soldeermachine Fieldmann
- Soldeermachine RIDGID
- Soldeermachine Craftsman
- Soldeermachine Yato
- Soldeermachine Cigweld
- Soldeermachine Epcom
- Soldeermachine Uten
- Soldeermachine Edsyn
- Soldeermachine Mag-Torch
- Soldeermachine UNIMIG
- Soldeermachine Ersa
- Soldeermachine Portasol
- Soldeermachine JBC
- Soldeermachine Hakko
- Soldeermachine Fixpoint
Nieuwste handleidingen voor Soldeermachine
18 April 2024
27 Maart 2024
27 Maart 2024
27 Maart 2024
27 Maart 2024
27 Maart 2024
26 Maart 2024
26 Maart 2024
18 Maart 2024
4 Maart 2024