Extron USB Plus Matrix Controller Handleiding

Bekijk gratis de handleiding van Extron USB Plus Matrix Controller (12 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 161 mensen en kreeg gemiddeld 4.4 sterren uit 9 reviews. Heb je een vraag over Extron USB Plus Matrix Controller of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1

USB Plus Matrix Controller • Setup Guide

The Extron® USB Plus Matrix Controller is a pre-congured controller that can easily be setup and deployed to control Extron

USBExtenderPlus products in a USB Matrix switching application within a gigabit Ethernet network. Quick and easy setup of

the USBPlusMatrixController, USB Extender Plus transmitters and receivers is done using Extron Product Conguration Soft-

ware (PCS). An Extron Control System or any third party control can interface with the USB Plus Matrix Controller via Ethernet or

RS-232 to perform USB switching.

The main components in a USB Extender Plus Matrix system:

• USB Plus Matrix Controller — The controller is pre-congured to control the USB Extender Plus transmitters and receivers

in a USB Matrix switching application. The default Telnet port is 22123 (see the USB Plus Matrix Controller Help File for full

details).

• USB Plus Extenders (transmitters and receivers) — At least 1 transmitter and 1 receiver are required, and up to 64

extenders total may be included. Each extender must be assigned a unique IP address (DHCP cannot be used to assign

these addresses), and these addresses are uploaded to the USB Plus Matrix Controller. All twisted pair models are supported:

rack mountable models (standard and HID-only), AAP™ models, and decorator-style models (see the USB Extender Plus

Series User Guide, available on www.extron.com, for more information about these models).

• Product Configuration Software (PCS) — This free software is loaded on the computer and is used to congure the

USB Extender Plus transmitters and receivers. It is also used to create a conguration that is uploaded to the USB Matrix

Controller (see the USB Plus Matrix Controller Help File for details on how to use PCS with the USB Matrix Controller).

• Extron Toolbelt — This free software is used to congure the IP settings of the USB Matrix Controller (see the Toolbelt Help

File at www.extron.com for details on how to use Toolbelt).

Installation

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.

• Do not perform a Mode 5 reset (see USB Plus Matrix Controller Help File) to the USB Matrix Controller. Doing so will

erase the factory loaded conguration used to control the USB Extender Plus transmitters and receivers.

• N’effectuez aucune réinitialisation complète de système (mode 5) (voir USB Plus Matrix Controller Help File) sur l’USB

Matrix Controller. Cette action entraînera en effet la suppression de la conguration par défaut, utilisée pour le contrôle

des émetteurs et récepteurs USBExtenderPlus.

The following diagram shows an example of a USB Plus Matrix Controller system setup:

USB EXTENDER Plus R

CONFIG

PAIR

STATUS

LINK

HOST

1

3

2

4

Rx 1

USB EXTENDER Plus R

CONFIG

PAIR

STATUS

LINK

HOST

1

3

2

4

Rx 2

USB EXTENDER Plus R

CONFIG

PAIR

STATUS

LINK

HOST

1

3

2

4

Rx 3

USB EXTENDER Plus R

CONFIG

PAIR

STATUS

LINK

HOST

1

3

2

4

Rx 4

LAN

Tx

1

USB EXTENDER Plus T

STATUS

LINK

HOST

CONFIG

PAIR

Tx

2

USB EXTENDER Plus T

STATUS

LINK

HOST

CONFIG

PAIR

Tx

3

USB EXTENDER Plus T

STATUS

LINK

HOST

CONFIG

PAIR

Tx

4

USB EXTENDER Plus T

STATUS

LINK

HOST

CONFIG

PAIR

USB Matrix Controller

ControlSystem

SIS (Simple Instruction Set Commands)

a

t

COM

RTS

CTS

Tx

Rx

R

USB PLUS MATRIX

C

C

o

t

n

t

ro

l

l

S

S

y

t

s

t

em

t

r

t

rix

C

ontrolle

r

S

I

S

(S

im

p

leIns

t

Control

Figure 1. Application Diagram of the USB Plus Matrix Controller System

1

Product specificaties