Extron FOX 3G HD-SDI P SM Handleiding

Bekijk gratis de handleiding van Extron FOX 3G HD-SDI P SM (2 pagina’s), behorend tot de categorie FAGYASZTÓK. Deze gids werd als nuttig beoordeeld door 12 mensen en kreeg gemiddeld 4.3 sterren uit 8 reviews. Heb je een vraag over Extron FOX 3G HD-SDI P SM of wil je andere gebruikers van dit product iets vragen? Stel een vraag

This guide provides instructions for an experienced installer to set up and operate

Extron

®

FOX 3G HD-SDI Transceiver.

The transceiver can be configured via its rear panel Mode DIP switches to operate in one

of three ways:

• Bidirectional transceiver

• Transmitter

• Receiver

See Transceiver Configurations on the rear of this guide if you need more information.

NOTE:In this guide, the term “transceiver” refers to any FOX 3G HD-SDI; the term “bidirectional transceiver” refers to a

FOX 3G HD-SDI specifically configured as a bidirectional transceiver.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the transceiver as required.

Step 2 — Connections and Initial Settings

a

HD-SDI Input connector —If the FOX 3G HD-SDI is configured as

either a bidirectional transceiver or as a transmitter, connect an

HD-SDI, SDI, or 3G-SDI video input to this BNC connector.

b

Mode switches — Set these DIP switches to the

positions shown at right to select the transceiver

configuration. See Transceiver Configurations on the

rear of this guide for more information.

c

Fiber optic connectors —

WARNING:This unit outputs continuous invisible light, which may be harmful to the eyes; use with caution. For

additional safety, plug the attached dust caps into the optical transceivers when the fiber optic cable is

unplugged.

NOTE:Ensure that you use the proper fiber cable for your transceivers. Typically, singlemode fiber cable has a

yellow jacket and multimode fiber cable has an orange or aqua jacket.

Tx connector — In any configuration, connect a fiber optic cable to the Optical Tx LC connector.

Connect the free end of this fiber optic cable to the Optical Rx connector on another FOX 3G HD-SDI transceiver that is

configured as a bidirectional transceiver or as a receiver.

Rx connector — In either the bidirectional transceiver or receiver configuration, connect a fiber optic cable to the

Optical Rx connector to receive the signal from the transmitting unit. Connect the free end as detailed below:

• In a 2-transceiver system, connect the free end of this cable to the Optical Tx connector on the transmitting unit,

which is configured as a transmitter.

• In a daisy-chained system, connect the free end of this cable to the Optical Tx connector on the previous unit in the

daisy chain (configured as either a bidirectional transceiver or a transmitter).

d

Buffered Outputs connectors —In any FOX 3G HD-SDI configuration, connect a digital display to these BNC connectors.

In the bidirectional transceiver configuration, connectors 1 and 2 both output the video that is sent from the other

transceiver.

In the receiver configuration, only connector 2 outputs video and it is the

video sent by the transmitting unit.

In the transmitter configuration, connectors 1 and 2 both output the video

signal that is input on the HD/SDI Input connector,

a

, on the same transceiver.

e

Plug the included external 12 VDC power supply into this Power connector —

2-pole captive screw connector as shown at right. Use the supplied tie-wrap to

strap the power cord to the extended tail of the connector.

12V

0.3A MAX

FOX HDSDI

HD/SDI IN

POWER

BUFFERED OUTPUTS

MODE

OPTICAL

RxTx

12

12

251

34

SW2Mode

Down

Down

Up

Up

Down

Up

Down

Up

Bidirectional transceiver ()default position

Transmitter with local monitor outputs

Receiver with daisy chaining

Spare (functions as receiver with daisy chaining)

SW1

MODE

12

Power Supply

Output Cord

SECTION

A–A

Ridges

Smooth

AA

Tie Wrap

3

5

1

FOX 3G HD-SDI Setup Guide

Product specificaties