Extech AUT30 Handleiding

Bekijk gratis de handleiding van Extech AUT30 (1 pagina’s), behorend tot de categorie Meetapparatuur. Deze gids werd als nuttig beoordeeld door 24 mensen en kreeg gemiddeld 4.0 sterren uit 8 reviews. Heb je een vraag over Extech AUT30 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

USER MANUAL

AU0-AUT30M-en-GB_V1.1 4/17 T3

Model AUT30 and AUT30M

Automotive 30A Current Testers

Features

•Large digit LCD display

•For use on standard ATC blade size fuse circuits (AUT30)

or mini- blade size fuse circuits (AUT30M)

•Measuring range to 30A/48VDC (10 sec. test time max.)

Safety

WARNING: Risk of Electrocution. Keep hands and fingers on

the body of the probe and away from the blade tips.

CAUTION: Read, understand and follow Safety Rules and

Operating Instructions in this manual before using meter.

Do not attempt to repair this unit. There are no user

serviceable parts.

Do not expose unit to extreme temperatures/high humidity

Do not use the unit if it is wet or damaged

Do not apply more than the rated voltage between the probe

tip and ground.

Do not operate with the case open

This symbol, adjacent to another symbol or terminal,

indicates the user the user must refer to the manual

for further information.

This symbol, adjacent to a terminal, indicates that,

under normal use, hazardous voltages may be present

Double insulation

Specifications

Range 0 to 30A DC / 48V DC

Resolution 10mA

Accuracy ± (2.0% ofreading+ 2 digits)

Detection distance <0.2”

Operating Temperature 0 to 50

o

C (32 to 122

o

F)

Storage Temperature20 to 60 -

o

C (-4 to 140

o

F)

Altitude 2000 meters(7000 ft.) maximum

Relative Humidity 80% up to 31

o

C (88

o

F), decreasing to

50% at 50

o

C (122

o

F)

Battery 1 x ‘A23G’ 12Vbattery

Dimensions/Weight159 x 25mm (6.25 x 1”) ) / 42g (1.5oz.

Cable length 71cm (2.3 )ft.

Operating Instructions

1.With the vehicle ignition OFF, remove the fuse from the

circuit to be tested and set it aside.

2.Insert the meter’s fuse blades (3) into the jack from where

the fuse was removed.

3.Insert the removed fuse into the meter’s fuse jack (4).

4.Press the meter’s On/Off button (2)

5.Operate the circuit under test for up to 10 seconds only; the

LCD (1) will display the measured current.

6.When finished press the On/Off button to turn off the tester.

7.WARNING! The Fuse blade may become hot during testing.

Allow to cool before removing. Do nottest > 10 seconds.

BATTERY INSTALLATION

1.To replace the battery, remove the screw from the back of

the unit and remove the cover.

2.Insert one 12V ‘A23G’ battery (observe polarity).

3.Replace the battery cover

NOTE: If the meter does not work properly, check the

battery to ensure that it’s fresh and properly inserted.

Battery Safety

Never dispose of batteries in a fire; batteries may explode or

leak.

Never dispose of used batteries or rechargeable

batteries in household waste.

As consumers, users are legally required to take used

batteries to appropriate collection sites, the retail

store where the batteries were purchased, or

wherever batteries are sold.

Disposal: Do not dispose of this instrument in household waste. The

user is obligated to take endes to a designated collection -of-life devic

point for the disposal of electrical and electronic equipment.

Copyright © - 20132017FLIR Systems, Inc.

All rights reserved including the right of reproduction in whole or in part in any form

ISO-9001 Certified

www.extech.com

Product specificaties