EXSYS EX-48210 Handleiding

Bekijk gratis de handleiding van EXSYS EX-48210 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.2 sterren uit 4 reviews. Heb je een vraag over EXSYS EX-48210 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

65

Die EX48210 ist eine M.2 Karte zur Umsetzung auf zwei RS422/485 Schnittstellen mit FIFO --

16C550 Port für den Anschluss von High Speed Seriellen RS-422/485 Peripherie Geräten (z.B.

Modem, Plotter usw.). Die EX48210 nutzt den Exar Chipsatz, der die neueste HighSpeed---

InterfaceTechnologie beinhaltet. Die Karte gewährleistet so eine sichere Datenübertragung und -

exzellente Performance von bis zu 921.6 KBaud/s für jedes angeschlossene serielle Gerät! Sie

unterstützt den M.2 NGFF Bus mit AKey. Es ist nicht möglich die I/O Adressen und Interrupts -

manuell einzustellen, da die Einstellungen der Karte vom System (BIOS) und beim installieren

des Betriebssystems automatisch vorgenommen werden.

Kompatibilität:M.2 NGFF mit AKey-

Betriebssysteme:Windows 200x/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux/ QNX 6.0

Anschlüsse:2x 9 Pin Stecker Seriell RS422/485-

Lieferumfang:EX48210, 2x Flachbandkabel, Treiber CD, Anleitung-

Zertifikate:

1

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

Anleitun

Vers. 1.0 / 20.02.19

E4821

ANSCHLÜSSE & JUMPERS

9 Pin Stecker Seriell

RS422 & RS485 4Draht---

PinSignalPinSignal

1TXD6NC-

2TXD+7NC

3RXD+8NC

4RXD9RI-

5GND

DB 9M

DRIVER INSTALLATION

Windows CE

After starting Windows is recognizes a new .Insert the driver CD into „Serial PCIConnector“-

you CDROM drive (eg drive D:) and then use the driver which located in the folder „windows -

CE 6 7“ (see picture):

Linux

After starting Linux is recognizes a new .Insert the driver CD into you „Serial PCIConnector“-

CDROM drive (eg drive D:) and then use the driver which located in the folder „Linux“ (see -

picture):

QNX

After starting the system is recognizes a new .Insert the driver CD into „Serial PCIConnector“-

you CDROM drive (eg drive D:) and then use the driver which located in the folder „QNX“ (see -

picture):

COM1&COM2: 2x 10 Pin Floppy Anschluss für

- RS422/485 9 Pin Flachbandkabel

JP3: Jumper zur Einstellung

des Mode am COM1

JP5: Jumper zur Einstellung

des Mode am COM2

HARDWAREINSTALLATION

DRIVER INSTALLATION

Please note the following installation instructions. Because there are large differences between the

PC’s, we can give you only a general installation instructions for the EX48210. Please refer your -

computer’s reference manual whenever in doubt.

1.Turn off the power to your computer and any other connected peripherals.

2.Remove the mounting screws located at the rear and/or sides panels of your Computer and

gently slide the cover off.

3.Now connect the two Ribbon Cable with the 10 Pin Floppy Connectors at the EX48210.-

4.Now set the Jumper JP3 & JP5 in the desired mode (see Connectors & Jumpers).

5.Locate an available M.2 NGFF expansion slot and insert the card. Make sure that the card is

plugged in correctly.

6.Gently replace your computer’s cover and the mounting screws.

Windows 200x/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx

After starting Windows is recognizes a new .Insert the driver CD into „Serial PCIConnector“-

you CDROM drive (eg drive D:) and then start the installer -„xr17v35x_win_single_installer“

which located in folder „Ver_5100_installer_uninstaller“ (see picture). Follow the installation

instructions and finish the installation:

CHECK INSTALLED DRIVER

Open the>DeviceManagerPorts (COM & LPT) Multiple -<. Now you should see at „“ and at„

Connection Adapter (serial) “the following new entry‘s:

If you see this or a similar information the device is installed correctly.

CONNECTORS & JUMPERS

JP3 & JP5

1

2

3

4

You have the option of operating the EX-48210 in RS422/485 4wire or --

RS485 2wire mode. For this purpose, you will find the following setting --

options at jumper JP3 (COM1) & JP5 (COM2).

1/2(Factory Setting) --=RS422/485 4wire

3/4 --=RS485 2wire

9 Pin Stecker Seriell

RS485 2Draht--

PinSignalPinSignal

1DATA6NC-

2DATA+7NC

3NC8NC

4NC9RI

5GND

Product specificaties