EverFocus EM900FP3 Handleiding

EverFocus Bewakingscamera EM900FP3

Lees hieronder de 📖 handleiding in het Nederlandse voor EverFocus EM900FP3 (15 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/15

EM900F eZ.HD Series

1080p Full High Definition

Micro Mini Metal Camera

User’s Manual

Release Date: February 6 201

Precautions

1. Do not install the camera near electric or magnetic fields. Install the camera away from

TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the

electromagnetic fields generated from these devices may distort the video image or

otherwise interfere with camera operation.

2. Never disassemble the camera beyond the recommendations in this manual nor introduce

materials other than those recommended herein. Improper disassembly or introduction of

corrosive materials may result in equipment failure or other damage.

3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may

cause permanent damage to the sensor and/or internal circuits, as well as creating

unbalanced illumination beyond the capability of the camera to compensate.

4. Keep the power cable away from water and other liquids and never touch the power cord

with wet hands. Touching a wet power cord with your hands or touching the power cord

with wet hands may result in electric shock.

5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may

result in equipment failure, electric shock or, in extreme cases, fire.

6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor

directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean

the sensor and the camera lens. Use a damp soft cloth to remove dirt from the camera any

body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any

part of the camera.

7. Do not operate the camera beyond the specified temperature, humidity or power source

ratings. This camera is suitable for indoor operation only. Use the camera at temperatures

within - 0 210°C~5 °C (14°F~11 °F) and humidity less than 80%; this device is not rated as

submersible. The input power source is 12VDC. Be sure to connect the proper + / - polarity

and voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail,

and such damage is not covered by the warranty.

8. Mounting. Use care in selecting a solid mounting surface which will support the weight of

the camera plus any wind, snow, ice or other loading, and securely attach the camera to the

mounting surface using screws and anchors which will properly support the camera. If

necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional

support for the camera.

Safety Notice

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and

can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Product specificaties

Merk:	EverFocus
Categorie:	Bewakingscamera
Model:	EM900FP3

Heb je hulp nodig?

Als je hulp nodig hebt met EverFocus EM900FP3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera EverFocus

EverFocus EQ350 Handleiding

9 Juli 2023

EverFocus EZN7221 Handleiding

9 Juli 2023

EverFocus ED200/N-3W Handleiding

9 Juli 2023

EverFocus EHN3261 Handleiding

9 Juli 2023

EverFocus EBD935 Handleiding

9 Juli 2023

EverFocus EQ250A/N Handleiding

9 Juli 2023

EverFocus EBD430 Handleiding

9 Juli 2023

EverFocus EM900FP4 Handleiding

8 Juli 2023

EverFocus EIVP-KBU-IV-V0004 Handleiding

8 Juli 2023

EverFocus EDN468ME Handleiding

8 Juli 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Sony SNC-VB640 Handleiding

26 April 2024

Sony SNC-EB642R Handleiding

26 April 2024

Sony SNC-VB642D Handleiding

26 April 2024

Sony SRG-HD1 Handleiding

26 April 2024

Sony SNC-ZM550 Handleiding

26 April 2024

Sony SNC-EM642R Handleiding

26 April 2024

Sony SNC-EM641 Handleiding

26 April 2024

Sony SNC-ZB550 Handleiding

26 April 2024

Sony SNC-VM602R Handleiding

26 April 2024

Sony SNC-DH110T Handleiding

26 April 2024